Low Cost Torch Height Control Install and Setup Manual - CandCNC
Low Cost Torch Height Control Install and Setup Manual - CandCNC
Low Cost Torch Height Control Install and Setup Manual - CandCNC
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
IN<br />
1<br />
2<br />
1<br />
2<br />
3<br />
1<br />
2<br />
3<br />
65<br />
Contrast<br />
VR1<br />
PWR<br />
C<strong>and</strong>CNC<br />
LCTHC REV4<br />
0710<br />
SIP1<br />
U14<br />
1<br />
C13<br />
J1<br />
U5<br />
R17<br />
U4<br />
G540 I/O<br />
J3<br />
1<br />
16<br />
J12<br />
3<br />
2<br />
TORCH<br />
ON<br />
THC<br />
DWN<br />
1<br />
THC<br />
UP<br />
LCTHC<br />
17<br />
1<br />
U2<br />
32 U10<br />
<strong>Torch</strong><br />
REMOTE<br />
ON/OFF<br />
J7<br />
D<br />
G<br />
S<br />
Q1<br />
R31<br />
1<br />
1<br />
U3 3<br />
Encoder<br />
2<br />
1<br />
TEST - 2<br />
+ 1 +<br />
J5<br />
12VDC<br />
THC SENSOR<br />
J6<br />
PC+5<br />
PCGND<br />
ARC<br />
OK<br />
IN<br />
+<br />
12VDC Bias<br />
WALLPLUG<br />
+<br />
TORCH<br />
PC+5<br />
DWN<br />
THC<br />
THC<br />
J3<br />
1<br />
32<br />
1<br />
-<br />
PCGND<br />
UP<br />
ON<br />
J6<br />
OK<br />
ARC<br />
J12<br />
G540 I/O<br />
+<br />
THC SENSOR<br />
65<br />
J5<br />
+<br />
12VDC<br />
To G540 Interface Card<br />
(OPTION)<br />
PC+5 (pullup source)<br />
See notes below on this signal<br />
COMMON RETURN (Com)<br />
Must be connected to the common<br />
return for the inputs. On a Isolated<br />
BoB that is the INPUT GND or INPUT<br />
COM. On non-isolated (inputs go<br />
stright through to PC parallel port) then<br />
this is connected to PC Ground<br />
Common Return (shown as PCGND on card) is needed on all installs. It’s connection<br />
point depends on what ground the inputs are connected to. On some systems (powered<br />
<strong>and</strong> isolated BoB’s) the Common Return is NOT PC Ground (or PCGND as stenciled on<br />
the LCTHC module). [ This name will be changed on the next release] See the different<br />
sections for hooking up the different types of connections. ONLY if the input connection<br />
is directly to the PC parallel port OR the BoB input is NOT isolated from the PC port do<br />
you use PCGND as the Common Return.<br />
For installs that do not have a BoB with opto isolator input OR a pull up resistor on each<br />
input of the BoB you must furnish a source of +5 that shares the same connection as the<br />
PC GND pin. The PC power supply has +5 <strong>and</strong> PC Ground on all of it’s power pins that<br />
connect drives to the PC power supply (internally). You can buy cables that will let you<br />
tap into the PC power wires to get the need +5.<br />
Page 27