Low Cost Torch Height Control Install and Setup Manual - CandCNC
Low Cost Torch Height Control Install and Setup Manual - CandCNC
Low Cost Torch Height Control Install and Setup Manual - CandCNC
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
J15<br />
Tip<br />
Volts<br />
Workclamp<br />
+ [POS]<br />
L4<br />
R7<br />
- [NEG]<br />
Electrode<br />
36 THC Sensor<br />
39<br />
REV 14<br />
L2<br />
L1<br />
J11<br />
37<br />
ARC OK<br />
J3<br />
Volts<br />
<strong>Torch</strong><br />
Switch<br />
J10<br />
+<br />
Arc<br />
J5<br />
D2<br />
OK<br />
J4<br />
TP4<br />
TP3<br />
TP1<br />
TP2<br />
38<br />
THC SENSOR CARD<br />
REV 14<br />
To TORCH -<br />
(ELECTRODE WIRES)<br />
DAMGER<br />
HIGH VOLTAGE<br />
WHEN TORCH<br />
is ON<br />
Mount card at least ½”from any<br />
Metal. Use ½”or longer st<strong>and</strong>offs<br />
above metal case Do not let shell<br />
of DB9 contact metal of<br />
Plasma Case<br />
TORCH SWITCH<br />
NO POLARITY<br />
R1<br />
J14<br />
Tip Volts<br />
D6<br />
CAUTION!<br />
HIGH VOLTAGE<br />
Spark Gap<br />
For HV Systems<br />
J17<br />
CAUTION!<br />
HIGH VOLTAGE<br />
RV1<br />
J16<br />
D13<br />
CAUTION!<br />
HIGH VOLTAGE<br />
C1<br />
R8<br />
TO TORCH POS<br />
(WORKCLAMP WIRE)<br />
TO ARC XFR<br />
[OK to Move]<br />
Relay Contacts<br />
(DRY CONTACTS)<br />
NO POLARITY<br />
R6<br />
FOR CT (Current<br />
Transformer) Input<br />
Only. See page<br />
information<br />
NOTE: BOARD Lettering<br />
(silkscreen) on REV14<br />
cards is REVERSED<br />
For J11 <strong>and</strong> J10.<br />
J10 is the <strong>Torch</strong> Switch<br />
Wires<br />
<strong>Torch</strong> Switch<br />
TORCH RELAY<br />
Arc OK[V]<br />
D22<br />
C<strong>and</strong>CNC<br />
D21<br />
TORCH<br />
ACTIVE<br />
ARC OK<br />
ARC OK LED<br />
ACTIVE ONLY<br />
WHEN CT INPUT<br />
is USED.<br />
DCP<br />
J3 is a<br />
DOUBLER<br />
DISABLE.<br />
When<br />
removed it<br />
will double<br />
the ARC OK<br />
VOLTS<br />
(used only<br />
with CT<br />
Transformer<br />
install)<br />
J1<br />
1<br />
5<br />
VR2<br />
6<br />
9<br />
PLUG<br />
SENSIVITY ADJUST<br />
FOR ARC OK FROM<br />
CT Transformer ONLY<br />
Not used with other<br />
ARC OK methods<br />
TP1 - TP2 Test voltage:<br />
When torch fired = approx<br />
1/7 of Rat TIP VOLTS.<br />
DB9 Cable to<br />
Connector on LCTHC<br />
Module<br />
Page 36
Change language