ENGINE SHOP REBUILD & SERVICE PARTS MANUAL - Jacobsen

More documents

Recommendations

Info

<strong>ENGINE</strong> REASSEMBLY A Follow numbers to tighten end cover bolts in correct sequence. Tighten to specified torque in two stages 9 7 4 1 5 2 3 8 6 (Some models may have 8 or 9 or 10 bolts) B Gently tap key into keyway Brass drift (Later models do not have a keyway) 21 Crankshaft Fig. D-9 Oil Pump Gear Rotors, Oil Pressure Switch, Pulser Coil and Fan Hub con’t Page D-14 Engine Shop Rebuild and Parts Manual
<strong>ENGINE</strong> REASSEMBLY Press lightly with suitable mandrel NOTE: For clarity, the fan is shown pulled away from the hub, and the fan hub is partially cut-a-way. It is not necessary to remove the fan or hub to set the air gap. Use the access holes provided. .020 - .039 Feeler gauge Insert phillips screwdriver through fan hub Fig. D-10 Pulser Coil Air Gap Engine Shop Rebuild and Parts Manual Page D-15
Page 1:
19 13 17 9 11 16 15 7 18 3 4 6 5 8
Page 4 and 5:
NOTES TO OBTAIN A COPY OF THE LIMIT
Page 6 and 7:
TABLE OF CONTENTS Section Page No.
Page 8 and 9:
TABLE OF CONTENTS Notes: Page vi En
Page 10 and 11:
HOW TO USE THIS MANUAL viii Engine
Page 12 and 13: ENGINE DISASSEMBLY Notes: Page A-ii
Page 14 and 15: ENGINE DISASSEMBLY D. Remove the ti
Page 16 and 17: 14 13 18 15 16 17 20 21 19 22 25 27
Page 18 and 19: ENGINE DISASSEMBLY A 2 6 3 Push spr
Page 20 and 21: ENGINE DISASSEMBLY Notes: Page B-ii
Page 22 and 23: ENGINE DISASSEMBLY Remove the Crank
Page 24 and 25: ENGINE DISASSEMBLY 1 3 2 Crankcase
Page 26 and 27: ENGINE DISASSEMBLY 1 5 4 6 3 2 A Se
Page 28 and 29: ENGINE DISASSEMBLY A 1 2 4 5 6 8 3
Page 30 and 31: ENGINE DISASSEMBLY Notes: Page B-10
Page 32 and 33: ENGINE MEASUREMENTS Notes: Page C-i
Page 34 and 35: ENGINE MEASUREMENTS F. Turn the cyl
Page 36 and 37: ENGINE MEASUREMENTS Measure each po
Page 38 and 39: 0 ENGINE MEASUREMENTS C 10 20 30 40
Page 40 and 41: ENGINE MEASUREMENTS Cylinder head C
Page 42 and 43: 0 50 0 50 ENGINE MEASUREMENTS Valve
Page 44 and 45: ENGINE MEASUREMENTS 1" Recommended
Page 46 and 47: ENGINE MEASUREMENTS Notes: Page C-1
Page 48 and 49: ENGINE REASSEMBLY Notes: Page D-ii
Page 50 and 51: ENGINE REASSEMBLY A. Apply a coat o
Page 52 and 53: ENGINE REASSEMBLY C. Using a depth
Page 54 and 55: ENGINE REASSEMBLY An electric drill
Page 56 and 57: ENGINE REASSEMBLY C 120 o Compressi
Page 58 and 59: ENGINE REASSEMBLY 14 12 8 2 13 4 7
Page 60 and 61: ENGINE REASSEMBLY Make sure the gea
Page 64 and 65: ENGINE REASSEMBLY Notes: Page D-16
Page 66 and 67: ENGINE REASSEMBLY Notes: Page E-ii
Page 68 and 69: ENGINE REASSEMBLY Install New Valve
Page 70 and 71: ENGINE REASSEMBLY Install the Front
Page 72 and 73: ENGINE REASSEMBLY A 8 7 6 1 3 2 5 B
Page 74 and 75: ENGINE REASSEMBLY 7 17 10 12 9 8 13
Page 76 and 77: ENGINE REASSEMBLY 29 31 27 28 25 23
Page 78 and 79: ENGINE REASSEMBLY B 3 2 1 4 Follow
Page 80 and 81: ENGINE REASSEMBLY 7 6 1 4 3 2 5 Fig
Page 82 and 83: ENGINE Illustrated Parts Breakdown
Page 96 and 97: LIMITED WARRANTY Notes: Page G-ii E
Page 98 and 99: LIMITED WARRANTY - FEDERAL deny war
Page 100 and 101: LIMITED WARRANTY - FEDERAL (2001) Y
Page 102 and 103: LIMITED WARRANTY - CALIFORNIA (1995
Page 112:
LIMITED WARRANTY - CALIFORNIA (2004
show all

ENGINE SHOP REBUILD & SERVICE PARTS MANUAL - Jacobsen

Create successful ePaper yourself

Delete template?

Save as template?