1 - Audio Intervisual Design, Inc.

More documents

Recommendations

Info

1-6 HD-1000 WORKSTATION Installing the HDSP Card To install the HDSP card, you will need: • A #2 Phillips screwdriver • The Power Macintosh CPU • The HDSP PCI card Figure 1-2 Installing PCI Expansion Cards To install the HDSP card: 1 Make certain that the Macintosh power is off. Disconnect the power cord. 2 Put on the static protection wrist band and attach the wire to a grounded terminal.
I NSTALLING T HE H ARDWARE 1-7 3 Open the Macintosh CPU (refer to the instructions that came with your computer) and locate the PCI expansion slots. 4 Remove the screw that holds the access cover for the third slot from the hinge in place. Remove the access cover and set it aside. 5 Unpack the HDSP card from its static-proof bag. Handle the card by its edges: don’t touch the gold connector fingers or on-board components. Note: If you’ve not already done so, write down the serial numbers for the HDSP Processor in the space provided on page vi of this manual. You’ll need this number if you require technical support. 6 Align the card’s connector fingers with the PCI slot and press down until the card is seated. Reinstall the screw to hold the card in place. 7 Follow steps 4–6 again to install a SCSI accelerator card if SCSI was not included with your CPU (refer to the documentation for the card to determine which slot to use). 8 Close the computer. You can now take off the wristband. Note: Reconnect the Macintosh power cord before continuing the installation. This will ensure that the computer is safely grounded, and thus prevent damage from differing ground potentials or stray electrostatic charges.
Page 2 and 3: ©2002 SonicStudio. All rights rese
Page 4 and 5: IV T ABLE OF C ONTENTS Overview of
Page 6 and 7: VI Related Documents Please refer t
Page 8 and 9: VIII keyfile. Warning! Before you a
Page 10 and 11: 1-2 HD-1000 WORKSTATION What’s In
Page 12 and 13: 1-4 HD-1000 WORKSTATION System Requ
Page 16 and 17: 1-8 HD-1000 WORKSTATION SCSI Bus Co
Page 18 and 19: 1-10 HD-1000 WORKSTATION 4 Using th
Page 20 and 21: 1-12 HD-1000 WORKSTATION To connect
Page 22 and 23: 1-14 HD-1000 WORKSTATION 2 Connect
Page 24 and 25: 2-2 S OFTWARE I NSTALLATION/DRIVE S
Page 32 and 33: 3-2 T HE S ONIC HD3 I/O BOX Overvie
Page 34 and 35: 3-4 T HE S ONIC HD3 I/O BOX Name De
Page 36 and 37: 3-6 T HE S ONIC HD3 I/O BOX Rear-Pa
Page 38 and 39: 3-8 T HE S ONIC HD3 I/O BOX AES/EBU
Page 40 and 41: 3-10 THE S ONIC HD3 I/O BOX If you
Page 42 and 43: 3-12 THE S ONIC HD3 I/O BOX This di
Page 44 and 45: 3-14 THE S ONIC HD3 I/O BOX The HD3
Page 46 and 47: 3-16 THE S ONIC HD3 I/O BOX OUTPUT
Page 48 and 49: 3-18 THE S ONIC HD3 I/O BOX
Page 50 and 51: A-2 C ONNECTOR W IRING HD3 Connecti
Page 52 and 53: A-4 C ONNECTOR W IRING
Page 54 and 55: FCC Statement This device complies
Page 56 and 57: Declaration of Conformity Applicati
Page 58: I-2 INDEX I formats 3-2, 3-7, 3-8 s

1 - Audio Intervisual Design, Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?