Download the full catalog - Schaff Piano Supply Co.

TECHNICIAN’S TOOLS
SCIORTINO HAND HELD COIL MAKER
The tuning pin is placed into the coil maker, and with the
depth gauge screw adjust the pin to the proper height. After
inserting the steel wire thru the becket hole and against the
hardened set screw on the coil maker, turn the pin with your
tuning pin crank to make perfect coils. Tool is 3-1/2” long.
No. 273 - Sciortino Coil Maker. Each
LOOPING MACHINE
Measuring 5-1/2” long by 1” wide, this aluminum casted
looper is designed to be clamped in a vise or to a
workbench. Both traditional bass string type loops and
German small coil loops can be made easily. Comes with
detailed instructions.
No. 115 - Looping Machine. Each
LOOPING MACHINE
Schaff has improved it’s looper to include hardened steel
inserts for the wire hold down clamp, and a casted
aluminum base for a permanent workbench installation.
Various length loops can be made with precision for the
plain wire strings in a piano. Comes with detailed
instructions.
No. 114 - Looping Machine. Each
TEFLON BUSHING INSERTER
A handy tool designed specifically for inserting
replacement teflon bushings into Steinway action parts.
Tool is 4-3/4” long, nickel plated.
No. 156 - Teflon Bushing Inserter. Each
BUTT PLATE INSERTER
Used for holding brass butt plates while installing brass
flange repair clips. Tool is 8-1/2” long, nickel plated with
plastic handle.
No. 128 - Butt Plate Inserter. Each
KEY BUSHING TIGHTENER
When a situation exists where either front or balance rail key
bushings have become enlarged causing rocking keys, this
tool enables the key bushings to be closed slightly. With the
tool’s unique design, all that is required is a gentle tap at the
end of the tightener. Tool is 4” long, nickel plated.
No. 148 - Key Bushing Tightener. Each
KEY TIGHTENER AND KEY EASER
This useful tool should be in every technician’s kit. One end
permits easing of the key pin hole without removing the key.
The reverse wedge in the other end enables oversize key pin
holes to be closed slightly to tighten the key.
No. 3105 - Key Tightener and Key Easer. Each
WEDGE KEY EASING TOOL
This 7” long, nickel plated tool is useful for easing the front
key pin hole without removing the key from the piano.
No. 272 - Wedge Key Easing Tool. Each
E-Z OUT EXTRACTORS
Reverse thread extractors for removing agraffes, tuning pins,
bolts, and screws. A hole is drilled in the broken part and
the extractor is inserted. Turned to the left, the spiral flutes
grip and remove the broken part without damaging the
threads in the hole. Extractors designed to work with our
#989 tap below.
No. 983 - #2 Extractor, for Broken Agraffes. Each
No. 3179 - #3 Extractor, for Broken Tuning Pins, Bolts
and Screws. Each
No. 984 - 7/64" Drill, for #2 Extractor. Each
No. 3180 - 5/32" Drill, for #3 Extractor. Each
989
985, 987
986, 988
AGRAFFE REPAIR DRILLS, TAPS AND TAP WRENCH
The following items are used in the replacement of either
7/32” or 1/4” diameter agraffes:
No. 985 - 7/32” dia. x 36 threads per inch Tap. Each
No. 986 - #11 Drill (.191) for use with No. 985 Tap. Each
No. 987 - 1/4” dia. x 36 threads per inch Tap. Each
No. 988 - #2 Drill (.221) for use with No. 987 Tap. Each
No. 989 - Tap Wrench for sizes 12 to 5/16”. Each
53