Download the full catalog - Schaff Piano Supply Co.

RESTRINGING TOOLS AND ACCESSORIES
COIL SETTER
Used for setting coil wire in even rows on the tuning pin,
thus eliminating any wire overlaps. The inside diameter of
hole is 5/16”, tool’s length is 5” with a black oxide finish.
No. 175 - Coil Setter. Each
COIL TIGHTENER
Round, hardened steel, with half cutout.
No. 3155 - Coil Tightener. Each
COIL SETTER-TIGHTENER
With the design of this tool, great leverage can be applied to
squeeze wire snug around tuning pins. Tool is 5-1/2” long,
3/4” diameter and has a black oxide finish.
No. 171 - Coil Setter-Tightener. Each
LOOP AND STRING SETTER
Used to level strings on the bridge, and to seat loops around
hitch pins. Solid brass, sold in pairs only.
No. 3161 - Loop and String Setter. Per Pair
TUNING PIN REAMERS OR SPOON BITS
When installing new or oversized tuning pins, it is
recommended that the holes be reamed. All of these reamers
are .009 under the diameter of the corresponding tuning pin
size and are 5-1/8” long.
Stock# For Pin size Size Diameter
137A 1/0 H .266"
137B 2/0 I .272"
137C 3/0 J .277"
137D 4/0 K .281"
137E 5/0 7.25mm .286"
TUNING PIN DRILLS
These drills have the preferred style brad point that will not
run or travel like the swedge tip type. Drills are 4-1/8” long
and, except for No. 136F are .009 under the diameter of the
corresponding tuning pin size.
Stock# For Pin size Size Diameter
136F 1/0 E .250"
136H 1/0 F .257"
136I 1/0, 2/0 G .261"
136E 1/0, 2/0 H .266"
136A 2/0 I .272"
136B 3/0 J .277"
136C 4/0 K .281"
136D
62
5/0 7.25mm .286"
TUNING PIN DRILLS
Slow spiral, plexi point drills measure 4-1/4” long and are
primarily designed for 2/0 pins in new pin blocks. 60 o point
prevents chipping out on the back of pin blocks.
No. 94A - Drill, .257 (F). Each
No. 94B - Drill, .261 (G). Each
No. 94C - Drill, .266 (H). Each
No. 94D - Drill, .272 (I). Each
TUNING PIN DRILLS - EXTRA LENGTH
These drills have the same specifications as our 94 Series
tuning pin drills above except that they are approx. 6-1/4"
long which make them ideal for drilling tuning pin holes
after the pin block is installed in the piano. Extra length
enables one to drill through the plate and into the pin block.
Stock# For Pin size Size Diameter
3290F 1/0 E .250"
3290H 1/0 F .257"
3290I 1/0, 2/0 G .261"
3290E 1/0, 2/0 H .266"
3290A 2/0 I .272"
3290B 3/0 J .277"
3290C 4/0 K .281"
3290D 5/0 7.25mm .286"
SCIORTINO INSTA-COILER
An amazing new stringing tool that will make a factory
perfect coil in seconds every time. Whether you are an
experienced stringer or not, this tool is extremely easy to use
and will eliminate the wear and tear on your fingers. The
Insta-Coiler is 5-1/2” long, about 3-1/2” high and comes with
complete instructions.
No. 122 - Sciortino Insta-Coiler. Each
BEARING CHECK GAUGE
A handy item for the restringing technician that gives a fast,
accurate and visual demonstration of bridge bearing to your
customer. Simply place the middle prong of the gauge on the
string between the bridge pins. Align the end prongs over the
same string and observe the amount of “rock” that occurs. If the
gauge cannot be “rocked” on either side of the bridge, then a
negative bearing situation is in effect and should be corrected.
Gauge is solid brass and measures 1-1/2” wide x 3-3/4” long.
No. 106 - Bearing Check Gauge. Each