5.Control system - Meibes
5.Control system - Meibes
5.Control system - Meibes
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
7. System examples<br />
7.1 Freshwater station with<br />
circulation in a time-slot<br />
and with tapping detection<br />
outside the time slot<br />
■ Initial operation and <strong>system</strong> calibration from point 6<br />
■ Setting the time and date, point 5.3.3<br />
■ Domestic hot ■ set value e.g.: 50°C, point<br />
water 5.3.3 and 5.3.5<br />
■ Circulation ■ Basic setting menu,<br />
Circulation submenu = select<br />
“on”, point 5.3.5<br />
■ In programming menu,<br />
circulation submenu up<br />
to 3 select time slot,<br />
point 5.3.3<br />
■ Circulation temperature 40°C,<br />
for control in time slot,<br />
point 5.3.5<br />
■ Circulation time e.g.: 60 s,<br />
Circulation rest time.: e.g.<br />
10 min, for controlling the<br />
circulation through tapping<br />
detection outside the<br />
time slot, point 5.3.5<br />
■ Heat transfer unit ■ WT = cold, point 5.3.3<br />
■ Time lag ■ e.g.: 20 s, point 5.3.5<br />
7.2 Freshwater station with<br />
circulation only via tapping<br />
detection<br />
■ Initial operation and <strong>system</strong> calibration from point 6<br />
■ Setting the time and date, point 5.3.3<br />
■ Domestic hot ■ set value e.g.: 50°C,<br />
water point 5.3.3 and 5.3.5<br />
■ Circulation ■ Basic setting menu,<br />
Circulation submenu = select<br />
“on”, point 5.3.5<br />
■ In programming menu,<br />
Circulation submenu is the<br />
start and stop times within<br />
each 3 time slots which are<br />
to be set at the same time<br />
e.g.: start 6h00 - stop 6h00<br />
point 5.3.3<br />
■ Circulation time e.g.: 60 s,<br />
Circulation rest time e.g.:<br />
10 min, point 5.3.5<br />
■ Heat transfer unit ■ WT = cold, point 5.3.3<br />
■ Time lag ■ e.g.: 20 s, point 5.3.5<br />
14<br />
7.3 Freshwater station without<br />
circulation<br />
■ Initial operation and <strong>system</strong> calibration from point 6<br />
■ Setting the time and date, point 5.3.3<br />
■ Domestic hot ■ set value e.g.: 50°C, point<br />
water 5.3.3 and 5.3.5<br />
■ Circulation ■ Basic setting menu,<br />
Circulation submenu = select<br />
“off”, point 5.3.5<br />
■ Heat transfer unit ■ WT = cold can be selected,<br />
if the distance between<br />
the buffer and the freshwater<br />
station is not too great.<br />
After-run e.g.: 20 s,<br />
point 5.3.5<br />
■ WT = hot can be selected,<br />
if there is a great distance<br />
between the buffer and the<br />
freshwater station, and the<br />
comfort of the “rapid” hot<br />
water drawing has been<br />
attained. Set the after-run<br />
point 5.3.5 on nought, as no<br />
circulation pipe is available.