U.S. DEPARTMENT OF TRANSPORTATION - SaferCar.gov

More documents

Recommendations

Info

TP-P572-V-00 CHECK SHEET NO. V6 THORAX WITHOUT ARM IMPACT TEST (S572.196) Pretest Preparation __1 Soak the dummy in a controlled environment at a temperature and relative humidity indicated in Table V6 for at least four hours prior to a test. Record the length of time for the soak and the maximum and minimum temperature and humidity in Table V6. Verify that each measurement meets specification by indicating “Pass” or “Fail” in the far right column. __2 Remove the arm on the impact side. __3 Install the thoracic and abdominal pads using cable ties 4 . __4 Place the chest jacket on the dummy. __5 The dummy should wear cotton underwear pants, cut off just above the knees, but no shirt or shoes. __6 Ground the dummy using a cable between a metal component of the dummy and the ground. __7 Align the upper and lower neck brackets so that the top edges are flush. __8 Place the bench in the pendulum’s impact area so that the dummy can be impacted in the thorax. __9 Seat the dummy on a sheet of 387 x 521 mm PTFE (Teflon) (2 mm thick) on the bench. Position the dummy within 25mm of the edge of the Teflon sheet; the edge of the sheet should be along the impact side of the bench’s seat pan (Figure 50). __10 Place a sheet of 514 x 514 mm PTFE (Teflon) (2 mm thick) between the seatback and the dummy’s posterior thorax; the edge of the sheet should be along the impact side of the bench’s seatback. __11 Position the dummy so that the centerline of impact probe is vertically centered on the centerline of the middle thoracic rib within 2 mm. This corresponds to a reference measurement of 93 2 mm below the centerline of the shoulder yoke assembly arm pivot when measured along a line parallel to the seatback (Figure 51). The center point of the impactor face is aligned horizontally with a line parallel to the seatback incline passing through the center of the shoulder yoke assembly arm pivot. The face of the impactor should be approximately parallel to, and just touching, the surface of the thorax, when the pendulum is at its lowest position during travel. Once the dummy is adjusted in the lateral and fore/aft directions, the impactor positioning with respect to the surface of the thorax jacket will be complete. 4 See Attachment of Thoracic and Abdominal Pads in the SID-IIsD. -51-
TP-P572-V-00 CHECK SHEET NO. V6 (Continued) THORAX WITHOUT ARM IMPACT TEST (S572.196) __12 Push the dummy’s chest towards the seatback, so that the back of the thorax is touching the seat. 514 x 514 x 2 mm Teflon 387 x 521 x 2 mm Teflon Figure 50. Thorax without arm impact test configuration for SID-IIsD -52-
Page 1 and 2:
Rev. 09/19/2012 SEPTEMBER 2012 U.S.
Page 3 and 4:
SINCAP MDB LABORATORY TEST PROCEDUR
Page 5 and 6:
SINCAP MDB LABORATORY TEST PROCEDUR
Page 7 and 8:
SINCAP MDB - 2 1. PURPOSE AND APPLI
Page 9 and 10:
SINCAP MDB - 4 2.3. TEST VEHICLE AS
Page 11 and 12:
SINCAP MDB - 6 schedule in cases of
Page 13 and 14:
SINCAP MDB - 8 (10) The position of
Page 15 and 16:
SINCAP MDB - 10 Figure 2 - Typical
Page 17 and 18:
SINCAP MDB - 12 D. A written calibr
Page 19 and 20:
SINCAP MDB - 14 before the MDB cont
Page 21 and 22:
SINCAP MDB - 16 shows not only curt
Page 23 and 24:
SINCAP MDB - 18 (2) Measure the dis
Page 25 and 26:
SINCAP MDB - 20 D. BARRIER PHOTOGRA
Page 27 and 28:
SINCAP MDB - 22 NOTE: The test labo
Page 29 and 30:
SINCAP MDB - 24 9.8 STILL PHOTOGRAP
Page 31 and 32:
SINCAP MDB - 26 No. 050 - Post-Test
Page 33 and 34:
SINCAP MDB - 28 NOTE: The numbering
Page 35 and 36:
SINCAP MDB - 30 (1) NHTSA Number (s
Page 37 and 38:
SINCAP MDB - 32 H. CALCULATION OF V
Page 39 and 40:
SINCAP MDB - 34 NOTE: The “As Tes
Page 41 and 42:
SINCAP MDB - 36 Figure 9 - Moving D
Page 43 and 44:
SINCAP MDB - 38 (1) With the seat
Page 45 and 46:
SINCAP MDB - 40 (6) If the seat and
Page 47 and 48:
SINCAP MDB - 42 seat controls the f
Page 49 and 50:
SINCAP MDB - 44 combined cable bund
Page 51 and 52:
SINCAP MDB - 46 NR NB Nose to Rim -
Page 53 and 54:
SINCAP MDB - 48 A B C D E F G H I J
Page 55 and 56:
SINCAP MDB - 50 C. MOVING DEFORMABL
Page 57 and 58:
SINCAP MDB - 52 A. MDB Centerline t
Page 59 and 60:
SINCAP MDB - 54 12.9 REMOVAL OF TES
Page 61 and 62:
SINCAP MDB - 56 F. TEST REPORT No t
Page 63 and 64:
SINCAP MDB - 58 M. The Contractor m
Page 65 and 66:
SINCAP MDB - 60 13.4 NOTIFICATION O
Page 67 and 68:
SINCAP MDB - 62 E. DRAFT TEST REPOR
Page 69 and 70:
SINCAP MDB - 64 H. DELIVERABLE SCHE
Page 71 and 72:
U.S. DEPARTMENT OF TRANSPORTATION T
Page 73 and 74:
List of Figures TP-P572-U-00 Figure
Page 75 and 76:
TP-P572-U-00 1. PURPOSE AND APPLICA
Page 77 and 78:
TP-P572-U-00 8. CALIBRATION AND TES
Page 79 and 80:
TP-P572-U-00 10. PRETEST REQUIREMEN
Page 81 and 82:
TP-P572-U-00 10. PRETEST REQUIREMEN
Page 83 and 84:
TP-P572-U-00 14. CHECK SHEETS CHECK
Page 85 and 86:
TP-P572-U-00 CHECK SHEET NO. U1 (Co
Page 87 and 88:
TP-P572-U-00 CHECK SHEET NO. U2 HEA
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
TP-P572-U-00 __4 __5 CHECK SHEET NO
Page 95 and 96:
Page 97 and 98:
TP-P572-U-00 CHECK SHEET NO. U4 SHO
Page 99 and 100:
TP-P572-U-00 CHECK SHEET NO. U5 RIB
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
TP-P572-U-00 CHECK SHEET NO. U7 ABD
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
TP-P572-U-00
Page 115 and 116:
TP-P572-V-00 Feb 2011 U.S. DEPARTME
Page 117 and 118:
TP-P572-V-00 List of Figures Figure
Page 119 and 120: TP-P572-V-00 List of Tables Table V
Page 121 and 122: TP-P572-V-00 3. SECURITY….Continu
Page 123 and 124: TP-P572-V-00 9. PHOTOGRAPHIC DOCUME
Page 125 and 126: TP-P572-V-00 10. PRETEST REQUIREMEN
Page 127 and 128: TP-P572-V-00 14. CHECK SHEETS CHECK
Page 129 and 130: TP-P572-V-00 CHECK SHEET NO. V1 (Co
Page 131 and 132: TP-P572-V-00 CHECK SHEET NO. V2 HEA
Page 149 and 150: TP-P572-V-00 CHECK SHEET NO.V3 (Con
Page 165 and 166: TP-P572-V-00 CHECK SHEET NO. V5 THO
Page 169: TP-P572-V-00 CHECK SHEET NO. V5 (Co
Page 181 and 182: TP-P572-V-00 PELVIS ACETABULUM IMPA
Page 185 and 186: TP-P572-V-00 CHECK SHEET NO. V10 PE
Page 187 and 188: TP-P572-V-00 CHECK SHEET NO. V10 (C
Page 193 and 194: ATTACHMENT OF THORACIC AND ABDOMINA
Page 195 and 196: P572-V-00
Page 197 and 198: P572-V-00
Page 199 and 200: SINCAP MDB - C2 ES-2re 50th Percent
Page 201 and 202: SINCAP MDB - C4 SID-IIs 5th Percent
Page 203 and 204: SINCAP MDB - C6 close to 20.0 degre
Page 205 and 206: SINCAP MDB - D1 APPENDIX D ALUMINIU
Page 207 and 208: SINCAP MDB - D3 FIGURE 1 2.3 Measur
Page 209 and 210: SINCAP MDB - D5 2.6 Crush Strength
Page 211 and 212: APPENDIX E. DELIVERABLE GUIDELINES
Page 213 and 214: 2 1. FINAL TEST REPORT Instructions
Page 215 and 216: 4 Block No. 1--REPORT NUMBER SINCAP
Page 217 and 218: 6 Block No. 17--KEY WORDS New Car A
Page 219 and 220: 8 Measurement Description Passenger
Page 221 and 222:
10 037 View of Disengaged Parking B
Page 223 and 224:
12 1.7 APPENDIX B - VEHICLE AND DUM
Page 225 and 226:
14 1.8 APPENDIX C - DUMMY PERFORMAN
Page 227 and 228:
16 Lower Spine Acceleration (G’s)
Page 229 and 230:
18 TABLE 4 - MDB Instrumentation MD
Page 231 and 232:
20 DATA SHEET NO. 1 (CONTINUED) GEN
Page 233 and 234:
22 DATA SHEET NO. 1 (CONTINUED) GEN
Page 235 and 236:
24 DATA SHEET NO. 2 (CONTINUED) SEA
Page 237 and 238:
26 DATA SHEET NO. 2 (CONTINUED) SEA
Page 239 and 240:
28 DATA SHEET NO. 4 DUMMY LATERAL C
Page 241 and 242:
30 DATA SHEET NO. 6 TEST VEHICLE AC
Page 243 and 244:
32 DATA SHEET NO. 8 POST-TEST OBSER
Page 245 and 246:
34 DATA SHEET NO. 9 MDB SUMMARY OF
Page 247 and 248:
36 DATA SHEET NO. 11 TEST VEHICLE E
Page 249 and 250:
38 DATA SHEET NO. 11 (CONTINUED) TE
Page 251 and 252:
40 DATA SHEET NO. 13 FMVSS NO. 301
Page 253 and 254:
42 3. FORMS Forms, like Data Sheets
Page 255 and 256:
44 1.1 Driver’s Seat 1.1A Seat Fo
Page 257 and 258:
1.2D Provide any other instructions
Page 259 and 260:
With the seat in the test seat trac
Page 261 and 262:
50 5. STEERING COLUMN AND WHEEL ADJ
Page 263 and 264:
52 9. DEACTIVATION OF SIDE AIRBAGS
Page 265 and 266:
___________________________________
Page 267:
56 Rev. 09/19/2012
Page 270 and 271:
FORM NO. 2 (CONTINUED) REPORT OF VE
Page 272 and 273:
FORM NO. 4 MONTHLY VEHICLE STATUS R
Page 274 and 275:
SINCAP MDB - F1 APPENDIX F Determin
Page 276 and 277:
SINCAP MDB - F3 (11) Again apply a
Page 278 and 279:
PROCEDURE FOR CHECKING AND RECORDIN
Page 280 and 281:
Figure 1 - Response of X Axis Accel
Page 282 and 283:
The channel outputs for the x-axis
Page 284 and 285:
Polarity Check Data Sheet For Y - A
show all

U.S. DEPARTMENT OF TRANSPORTATION - SaferCar.gov

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?