U.S. DEPARTMENT OF TRANSPORTATION - SaferCar.gov

More documents

Recommendations

Info

TP-P572-V-00 CHECK SHEET NO. V7 (Continued) ABDOMEN IMPACT TEST (S572.197) (208 mm) Dummy’s back against Figure 53. Impact probe position for the SID-IIsD abdomen __12 Push the dummy’s chest towards the seatback, so that the back of the thorax is touching the seat (Figure 53). __13 Push the femurs towards the seat pan so that the thighs are in contact with the seat. __14 Move the legs together so that the knees are touching (see Figure 43). __15 Position the feet so that they are vertical within 2, with the heels touching the surface of the support table (see Figure 44). __16 Adjust the dummy so that the thoracic lateral plane is 0 1 relative to horizontal (see Figure 45). __17 Adjust the dummy so that the thoracic fore/aft plane measures 24.6 2 relative to horizontal. This measurement can be taken at the top of the shoulder rib mount (see Figure 46). -57-
TP-P572-V-00 CHECK SHEET NO. V7 (Continued) ABDOMEN IMPACT TEST (S572.196) Conduct Test, Collect Data and Verify Performance __1 Record the room temperature and humidity in Table V7. Verify that the temperature and relative humidity meets specification by indicating “Pass” or “Fail” in the far right column __2 The impactor shall have a mass of 13.97 0.23 kg 6 with a 76.2 mm face 7 and a 12.7 mm radius. __3 Mount an accelerometer on the impactor with its sensitive axis in line with the longitudinal centerline of the impactor. __4 Release the impactor at an impact speed between 4.2 - 4.4 m/s. __5 At the instant of contact, the impactor shall be horizontal ± 1° and the centerline of the impactor shall be within 2 mm of the centerline of the abdominal ribs. __6 The data acquisition system should conform to SAE Recommended Practice J211. __7 The impactor and spine accelerations are collected and filtered using a Channel Class 180 phaseless filter. __8 The abdominal rib deflections are collected and filtered using a Channel Class 600 phaseless filter. __9 Time zero is defined as the time of contact between the impact probe and the abdomen. All channels should be at a zero level at this point. __10 Record the peak impactor acceleration, peak abdominal rib deflections and peak lower spine acceleration in Table V7. Verify that each measurement meets specification by indicating “Pass” or “Fail” in the far right column. __11 If test results do not meet specification, wait at least 30 minutes, conduct another test. __12 Record and report the test results of each additional test in a separate table. Table V7. Abdomen Impact Test Tested Parameter Units Specification Result Dummy Soak Time Minutes ≥180 Temperature - Max C 20.6 to 22.2 During Soak Min C Relative Humidity - Max % 10.0 to 70.0 During Soak Min % Temperature – During test C 20.6 to 22.2 Relative Humidity – During test % 10.0 to 70.0 Impactor Velocity m/s 4.2 to 4.4 Peak Upr Abdominal Rib Deflection mm 36 to 47 Peak Lwr Abdominal Rib Deflection mm 33 to 44 Peak Lower Spine (T12) Accel (Y) G’s 9 to 14 Peak Impactor Acceleration G’s 12 to 16 Pass/ Fail __________________________________ Signature ____________________ Completion Date 6 Mass includes impactor mass and all rigidly attached hardware, plus 1/3 of supporting cable weight. 7 Note that this impactor face differs from impactor faces used in the other certification tests. -58-
Page 1 and 2:
Rev. 09/19/2012 SEPTEMBER 2012 U.S.
Page 3 and 4:
SINCAP MDB LABORATORY TEST PROCEDUR
Page 5 and 6:
SINCAP MDB LABORATORY TEST PROCEDUR
Page 7 and 8:
SINCAP MDB - 2 1. PURPOSE AND APPLI
Page 9 and 10:
SINCAP MDB - 4 2.3. TEST VEHICLE AS
Page 11 and 12:
SINCAP MDB - 6 schedule in cases of
Page 13 and 14:
SINCAP MDB - 8 (10) The position of
Page 15 and 16:
SINCAP MDB - 10 Figure 2 - Typical
Page 17 and 18:
SINCAP MDB - 12 D. A written calibr
Page 19 and 20:
SINCAP MDB - 14 before the MDB cont
Page 21 and 22:
SINCAP MDB - 16 shows not only curt
Page 23 and 24:
SINCAP MDB - 18 (2) Measure the dis
Page 25 and 26:
SINCAP MDB - 20 D. BARRIER PHOTOGRA
Page 27 and 28:
SINCAP MDB - 22 NOTE: The test labo
Page 29 and 30:
SINCAP MDB - 24 9.8 STILL PHOTOGRAP
Page 31 and 32:
SINCAP MDB - 26 No. 050 - Post-Test
Page 33 and 34:
SINCAP MDB - 28 NOTE: The numbering
Page 35 and 36:
SINCAP MDB - 30 (1) NHTSA Number (s
Page 37 and 38:
SINCAP MDB - 32 H. CALCULATION OF V
Page 39 and 40:
SINCAP MDB - 34 NOTE: The “As Tes
Page 41 and 42:
SINCAP MDB - 36 Figure 9 - Moving D
Page 43 and 44:
SINCAP MDB - 38 (1) With the seat
Page 45 and 46:
SINCAP MDB - 40 (6) If the seat and
Page 47 and 48:
SINCAP MDB - 42 seat controls the f
Page 49 and 50:
SINCAP MDB - 44 combined cable bund
Page 51 and 52:
SINCAP MDB - 46 NR NB Nose to Rim -
Page 53 and 54:
SINCAP MDB - 48 A B C D E F G H I J
Page 55 and 56:
SINCAP MDB - 50 C. MOVING DEFORMABL
Page 57 and 58:
SINCAP MDB - 52 A. MDB Centerline t
Page 59 and 60:
SINCAP MDB - 54 12.9 REMOVAL OF TES
Page 61 and 62:
SINCAP MDB - 56 F. TEST REPORT No t
Page 63 and 64:
SINCAP MDB - 58 M. The Contractor m
Page 65 and 66:
SINCAP MDB - 60 13.4 NOTIFICATION O
Page 67 and 68:
SINCAP MDB - 62 E. DRAFT TEST REPOR
Page 69 and 70:
SINCAP MDB - 64 H. DELIVERABLE SCHE
Page 71 and 72:
U.S. DEPARTMENT OF TRANSPORTATION T
Page 73 and 74:
List of Figures TP-P572-U-00 Figure
Page 75 and 76:
TP-P572-U-00 1. PURPOSE AND APPLICA
Page 77 and 78:
TP-P572-U-00 8. CALIBRATION AND TES
Page 79 and 80:
TP-P572-U-00 10. PRETEST REQUIREMEN
Page 81 and 82:
TP-P572-U-00 10. PRETEST REQUIREMEN
Page 83 and 84:
TP-P572-U-00 14. CHECK SHEETS CHECK
Page 85 and 86:
TP-P572-U-00 CHECK SHEET NO. U1 (Co
Page 87 and 88:
TP-P572-U-00 CHECK SHEET NO. U2 HEA
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
TP-P572-U-00 __4 __5 CHECK SHEET NO
Page 95 and 96:
Page 97 and 98:
TP-P572-U-00 CHECK SHEET NO. U4 SHO
Page 99 and 100:
TP-P572-U-00 CHECK SHEET NO. U5 RIB
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
TP-P572-U-00 CHECK SHEET NO. U7 ABD
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
TP-P572-U-00
Page 115 and 116:
TP-P572-V-00 Feb 2011 U.S. DEPARTME
Page 117 and 118:
TP-P572-V-00 List of Figures Figure
Page 119 and 120:
TP-P572-V-00 List of Tables Table V
Page 121 and 122:
TP-P572-V-00 3. SECURITY….Continu
Page 123 and 124:
TP-P572-V-00 9. PHOTOGRAPHIC DOCUME
Page 125 and 126: TP-P572-V-00 10. PRETEST REQUIREMEN
Page 127 and 128: TP-P572-V-00 14. CHECK SHEETS CHECK
Page 129 and 130: TP-P572-V-00 CHECK SHEET NO. V1 (Co
Page 131 and 132: TP-P572-V-00 CHECK SHEET NO. V2 HEA
Page 149 and 150: TP-P572-V-00 CHECK SHEET NO.V3 (Con
Page 165 and 166: TP-P572-V-00 CHECK SHEET NO. V5 THO
Page 175: TP-P572-V-00 CHECK SHEET NO. V7 (Co
Page 181 and 182: TP-P572-V-00 PELVIS ACETABULUM IMPA
Page 185 and 186: TP-P572-V-00 CHECK SHEET NO. V10 PE
Page 187 and 188: TP-P572-V-00 CHECK SHEET NO. V10 (C
Page 193 and 194: ATTACHMENT OF THORACIC AND ABDOMINA
Page 195 and 196: P572-V-00
Page 197 and 198: P572-V-00
Page 199 and 200: SINCAP MDB - C2 ES-2re 50th Percent
Page 201 and 202: SINCAP MDB - C4 SID-IIs 5th Percent
Page 203 and 204: SINCAP MDB - C6 close to 20.0 degre
Page 205 and 206: SINCAP MDB - D1 APPENDIX D ALUMINIU
Page 207 and 208: SINCAP MDB - D3 FIGURE 1 2.3 Measur
Page 209 and 210: SINCAP MDB - D5 2.6 Crush Strength
Page 211 and 212: APPENDIX E. DELIVERABLE GUIDELINES
Page 213 and 214: 2 1. FINAL TEST REPORT Instructions
Page 215 and 216: 4 Block No. 1--REPORT NUMBER SINCAP
Page 217 and 218: 6 Block No. 17--KEY WORDS New Car A
Page 219 and 220: 8 Measurement Description Passenger
Page 221 and 222: 10 037 View of Disengaged Parking B
Page 223 and 224: 12 1.7 APPENDIX B - VEHICLE AND DUM
Page 225 and 226: 14 1.8 APPENDIX C - DUMMY PERFORMAN
Page 227 and 228:
16 Lower Spine Acceleration (G’s)
Page 229 and 230:
18 TABLE 4 - MDB Instrumentation MD
Page 231 and 232:
20 DATA SHEET NO. 1 (CONTINUED) GEN
Page 233 and 234:
22 DATA SHEET NO. 1 (CONTINUED) GEN
Page 235 and 236:
24 DATA SHEET NO. 2 (CONTINUED) SEA
Page 237 and 238:
26 DATA SHEET NO. 2 (CONTINUED) SEA
Page 239 and 240:
28 DATA SHEET NO. 4 DUMMY LATERAL C
Page 241 and 242:
30 DATA SHEET NO. 6 TEST VEHICLE AC
Page 243 and 244:
32 DATA SHEET NO. 8 POST-TEST OBSER
Page 245 and 246:
34 DATA SHEET NO. 9 MDB SUMMARY OF
Page 247 and 248:
36 DATA SHEET NO. 11 TEST VEHICLE E
Page 249 and 250:
38 DATA SHEET NO. 11 (CONTINUED) TE
Page 251 and 252:
40 DATA SHEET NO. 13 FMVSS NO. 301
Page 253 and 254:
42 3. FORMS Forms, like Data Sheets
Page 255 and 256:
44 1.1 Driver’s Seat 1.1A Seat Fo
Page 257 and 258:
1.2D Provide any other instructions
Page 259 and 260:
With the seat in the test seat trac
Page 261 and 262:
50 5. STEERING COLUMN AND WHEEL ADJ
Page 263 and 264:
52 9. DEACTIVATION OF SIDE AIRBAGS
Page 265 and 266:
___________________________________
Page 267:
56 Rev. 09/19/2012
Page 270 and 271:
FORM NO. 2 (CONTINUED) REPORT OF VE
Page 272 and 273:
FORM NO. 4 MONTHLY VEHICLE STATUS R
Page 274 and 275:
SINCAP MDB - F1 APPENDIX F Determin
Page 276 and 277:
SINCAP MDB - F3 (11) Again apply a
Page 278 and 279:
PROCEDURE FOR CHECKING AND RECORDIN
Page 280 and 281:
Figure 1 - Response of X Axis Accel
Page 282 and 283:
The channel outputs for the x-axis
Page 284 and 285:
Polarity Check Data Sheet For Y - A
show all

U.S. DEPARTMENT OF TRANSPORTATION - SaferCar.gov

Create successful ePaper yourself

Delete template?

Save as template?