Isis Installation Guide - Big Ass Fans

More documents

Recommendations

Info

6 Fan diagram Isis ® Refer to the diagram below to identify the fan components. Note: Fan setup may differ from the illustration depending on the required mounting method. The safety cable is not pictured below; however, it is an important part of the installation. A. Upper mount. B. Extension tube. Extends the fan from the ceiling and provides a path for wiring. C. Main fan unit. Includes motor, hub, lower mount, and power wire. D. Airfoil. E. Winglet. ® fans; however, airfoil tips are available as an option. WWW.BIGASSFANS.COM ©2014 DELTA T CORP. DBA BIG ASS FAN CO. ALL RIGHTS RESERVED
Preparing the work site Isis ® 7 The fan should only be installed according to the instructions described in this manual. Consult a structural engineer for installation methods not covered in this manual. For optional mounting methods, refer to the installation instructions included with the fan parts. When surveying the work site, keep the following mechanical and electrical guidelines in mind. Mechanical • A suitable means for lifting the weight of the fan, such as a scissor lift, and at least two installation personnel will be required. • single purlin, truss, or bar joist. Consult a structural engineer for installation methods not covered in this manual. • • If mounting the fan in the vicinity of an infrared/radiant heater, it is recommended that the fan be mounted outside of the clearances recommended by the manufacturer of the heater and at a height equal to or above the shielding on the heating element with the controller on the opposite side of the heater. If mounting the fan below the heater shielding, all fan elements must be outside of the the minimum clearance to combustibles (MCC). • locations.” • Adhere to the safety requirements in the table below when selecting where to mount the fan. Safety requirement Clearance Blade height HVAC equipment Fan spacing Radiant/IR heaters Minimum distances obstructions such as lights, cables, or other building structure. If the fan is mounted at the same level or higher than a diffuser, the winglets must be at a distance that is at least 1x the measure of the fan’s diameter. HVAC Diffuser (8 ft) (2.4 m) HVAC Diffuser (16 ft) (4.9 m) If the fan is mounted below a diffuser, the winglets must be at a distance that is at least 2x the measure of the fan’s diameter. Electrical • Identify the existing wiring to determine which wiring application is needed to install the fan. • If installing a 120 V fan on a typical lighting circuit with one basic light switch in which the critical red conductor or “traveler” is absent, you will need to purchase the Limited Access Controller. Please discuss this option with your Big Ass Fans representative. • Isis ® is shipped with either a 110–125 VAC motor or a 200–240 VAC motor. The fan’s voltage is marked on the fan packaging and on the label on top of the main fan unit. The voltage cannot be changed during installation. Ensure your fan is the correct voltage prior to beginning installation. WWW.BIGASSFANS.COM ©2014 DELTA T CORP. DBA BIG ASS FAN CO. ALL RIGHTS RESERVED
Page 1 and 2: INSTALLATION GUIDE Isis ® For help
Page 3 and 4: Isis ® Installation Guide Isis ®
Page 5 and 6: Isis ® Reference Guide The followi
Page 7 and 8: Isis ® Contents General Informatio
Page 9 and 10: About this fan Isis ® Introduction
Page 11 and 12: Parts included Isis ® 3 Note: Dr
Page 13: Tools needed Isis ® 5 Big Ass Fan
Page 17 and 18: Isis ® Mounting Structure: Bar Joi
Page 23 and 24: Isis ® Mounting Structure: Wood Fr
Page 25 and 26: Isis ® Mounting Structure: Wood Fr
Page 27 and 28: Isis ® Mounting Structure: Solid B
Page 29 and 30: Isis ® Hanging the Fan (cont.) 21
Page 31 and 32: Isis ® Installing Guy Wires (cont.
Page 33 and 34: Isis ® Installing Airfoils 25 Big
Page 35 and 36: Isis ® Electrical Installation 27
Page 37 and 38: Isis ® Electrical Installation (co
Page 39 and 40: ® ) Isis ® Electrical Installatio
Page 41 and 42: Isis ® Fan Operation 33 120 V Isis
Page 43 and 44: Isis ® Alternative Wiring Methods
Page 45 and 46: 3-way single fan application Isis
Page 47 and 48: Isis ® Troubleshooting 39 WARNING:
Page 49: Annual Maintenance Checklist Fan Mo
Page 53 and 54: Isis ® Warranty Return Instruction
Page 55 and 56: Warranty Claim Form 800 Winchester
Page 57 and 58: Check-In Procedure (for Big Ass 23
Page 59 and 60: (for Big Ass 2348 Innovation Drive
Page 61 and 62: MANUEL D’INSTALLATION Isis ® Pou
Page 63 and 64: Isis ® ® i janvier 2014 Rév.
Page 65 and 66:
Isis ® Les instructions fournies
Page 67 and 68:
Isis ® Consignes de sécurité i
Page 69 and 70:
Isis ® Ass attirons votre atte
Page 71 and 72:
Isis ® Avant l'installation (suite
Page 73 and 74:
Page 75:
Page 78 and 79:
Isis ® Ø 1,4 cm (9/16 po)
Page 80 and 81:
Isis ® fournie par le client,
Page 82 and 83:
Isis ® Repérez, sur l
Page 84 and 85:
Isis ® prévue à cet effet,
Page 86 and 87:
Isis ® un ingénieur-ar
Page 88 and 89:
Isis ® pour tige de prolongat
Page 90 and 91:
Isis ® les attaches pour
Page 92 and 93:
Isis ® ® ou une clé Allen
Page 94 and 95:
Isis ® retenue doit être p
Page 96 and 97:
Isis ® ® Installation électri
Page 98 and 99:
Isis ® Installation électrique (s
Page 100 and 101:
Isis ® Installation électrique (s
Page 102 and 103:
Isis ® Ass Fan présente des per
Page 104 and 105:
Isis ® Autres techniques de raccor
Page 106 and 107:
Isis ® procédure de dé
Page 108 and 109:
Isis ® endommagés, puis remette
Page 111:
Veuillez remplir ce bon de commande
Page 114 and 115:
Isis ® 1. Remplissez le formulai
Page 116 and 117:
Ass Fan www.bigassfans.com re
Page 118 and 119:
(formulaire réservé aux installat
Page 120:
(formulaire réservé aux installat
show all

Isis Installation Guide - Big Ass Fans

Create successful ePaper yourself

Delete template?

Save as template?