Series CR Installation Manual PDF - Myers Power Products, Inc.

More documents

Recommendations

Info

Location Guidelines: CAUTION • Choose a permanent location for the unit. Attempting to move them after you have installed the batteries can damage the batteries and the cabinet. This equipment is heavy. Refer to Table 3.4 when you choose a site to make sure that the floor can support the weight of the system, the batteries, and any other necessary equipment. Table 3.4 System weight [in lbs. (kg)] System Models for 90 Minute run time Unit with Standard SLC Batteries Unit without Batteries Single Phase Three Phase 3.0kw 4.0kw 5.0kw 6.5kw 8.0kw 4.0kw 5.0kw 6.5kw 8.0kw 1545 (696) 805 (362) 1693 (763) 805 (362) 1990 (896) 805 (362) 2285 (1029) 805 (362) 2580 (1162) 805 (362) 1693 (763) 805 (362) 1990 (896) 805 (362) 2285 (1029) 805 (362) 2580 (1162) 805 (362) 11 114306E—Install/User <strong>Manual</strong>
Receiving and Moving the Unit and the Batteries Systems weigh several hundred pounds; (see Table 3.4; ask your sales representative for additional information). Make sure you are prepared for these weights before you unload or move the unit or the batteries. Do not install any batteries until you have permanently installed the unit and any battery cabinets and connected all conduit and wiring. Storage and Operating Environment Make sure you store the system in a clean, cool, dry place with normal ventilation and level floors. Storage Temperature Store the batteries (in the system) at -18 to 40°C (0 to 104°F). Batteries have a longer shelf life if they are stored below 25°C (77°F). Keep stored batteries fully charged. Recharge the batteries every 90– 180 days. The system without batteries may be stored at -20 to 70°C (-4 to 158°F). Ventilation The air around the unit must be clean, dust-free, and free of corrosive chemicals or other contaminants. Do not place the system or batteries in a sealed room or container. Operating Temperature System can operate from -20 to 40° (-4 to 104°F) and up to 95% relative humidity. The batteries’ service life is longer if the operating temperature stays below 25°C (77°F). Batteries The temperature should be near 25°C (77°F) for optimum battery performance. Batteries are less efficient at temperatures below 18°C (65°F), and high temperatures reduce battery life. Typically, at about 35°C (95°F), battery life is half of what it would be at a normal temperature of 25°C (77°F). At about 45°C (113°F), battery life is one-fourth of normal. Make sure that heaters, sunlight, air conditioners, or outside air vents are not directed toward the batteries. These conditions can make the temperature within battery strings vary, which can cause differences in the batteries’ voltages. Eventually, these conditions affect battery performance. If the batteries are not in the system, remember that the batteries should be installed as close as possible to the unit to reduce DC wiring costs and improve battery performance. Do not allow tobacco smoking, sparks, or flames in the system location because hydrogen is concentrated under the vent cap of each cell of the battery. Hydrogen is highly explosive, and it is hard to detect because it is colorless, odorless, and lighter than air. Every type of battery can produce hydrogen gas, even sealed maintenance-free batteries. The gas is vented through the vent caps and into the air, mainly when the unit is charging the batteries. The batteries produce the most hydrogen when maximum voltage is present in fully charged batteries. The amount of current that the charger supplies to the batteries (not the battery ampere-hour) determines how much hydrogen is produced. High Altitude Operation The maximum operating ambient temperature drops 1°C per 300m (2°F per 1000 ft) above sea level. Maximum elevation is 3000m (10,000 ft). 12 114306E—Install/User <strong>Manual</strong>
Page 1 and 2: INSTALLATION & USER’S GUIDE 3kW -
Page 3 and 4: C A U T I O N READ ENTIRE MANUAL AN
Page 5 and 6: SECTION 9 Options………………
Page 7 and 8: BATTERY STORAGE WARNING This shipme
Page 9 and 10: Record Keeping An on-site permanent
Page 11: SECTION 3 BEFORE INSTALLING THE SYS
Page 15 and 16: SECTION 4 AC INPUT & AC OUTPUT INST
Page 17 and 18: Table 4.2 Recommended Minimum Wire
Page 19 and 20: SECTION 5 INSTALLING BATTERIES AND
Page 21 and 22: Before Installing the Batteries Too
Page 23 and 24: Connecting the Cables Between Batte
Page 25 and 26: CAUTION Do not dispose of batteries
Page 27 and 28: BATTERY RETAINER BRACKET (TB1) INPU
Page 29 and 30: BRACKET BATTERY RETAINER DC FUSE (F
Page 31 and 32: SECTION 6 STARTUP AND SHUTDOWN PROC
Page 33 and 34: MAINTENANCE BYPASS PROCEDURE CAUTIO
Page 35 and 36: SECTION 8 FRONT PANEL DISPLAY The F
Page 37 and 38: Control Functions Control functions
Page 39 and 40: The Day of the Automatic Tests Tabl
Page 41 and 42: 3-PHASE SYSTEM: 1-POLE OUTPUT CIRCU
Page 43 and 44: REMOTE SUMMARY ALARM PANEL SCHEMATI
Page 45 and 46: SECTION 10 RS232 OPERATION 1.0 INTR
Page 47 and 48: 4.0 COMMANDS Meter Functions 4.1 Ge
Page 49 and 50: 4.7 Get Battery Current PC Interfac
Page 51 and 52: 5.8 Get Output Current Load Reducti
Page 53 and 54: 5.21 Get Alarm Log PC Interface: Sy
Page 55 and 56: LOCATION OF THE RS232 PORT RS232 po
Page 57 and 58: Fig. 10.5 56 114306E—Install/User
Page 59 and 60: SECTION 11 SPECIFICATIONS Input Out
Page 61 and 62: 60 THE NUMBER IN THE CHART INDICATE
Page 63 and 64:
Heater Option Operation: The Heater
Page 65 and 66:
SECTION 15 WARRANTY RETURN MATERIAL
Page 67:
66 114306E—Install/User Manual
show all

Series CR Installation Manual PDF - Myers Power Products, Inc.

Create successful ePaper yourself

Delete template?

Save as template?