Series CR Installation Manual PDF - Myers Power Products, Inc.

More documents

Recommendations

Info

6. Install only the battery string fuses( on the battery shelf). Next, use the voltmeter to check the DC voltage between the negative (-) position on the battery block and the unconnected battery positive terminal. This voltage should be approximately the battery voltage record on the unit ID label. If it is greater than + or – 5% Vdc, review the battery wiring diagram. Correct any wiring errors and recheck the DC voltage; do not go on until your measurement is within + or – 5% Vdc. If the measurement is too high and you cannot find the cause of the problem, call SERVICE. CAUTION If you do not verify that voltage and current direction are correct, the equipment may fail. Connecting the Positive Battery Cable(s) to the Battery String(s) Remove the insulation from the cable that was put on in step 2 of “Electronics cabinet battery block connections”. Connect the cable to the battery positive (+). Repeat this step for systems with 2 strings. Replacing the Batteries CAUTION A battery can present a risk of electrical shock and high short circuit current. A qualified electrician familiar with battery systems should service the batteries. Review all the safety instructions at the beginning of this chapter before you replace any batteries. Use the Same Quantity and Type of Battery CAUTION You must use the same quantity and type of battery. Substituting batteries not supplied by manufacturer voids the UL (CUL) listing and may cause equipment damage. To ensure continued superior performance of your system and to maintain proper charger operation, you must replace the batteries in the system or battery cabinets with the same number of batteries. These batteries must be the same types as the original batteries. The replacement batteries should have the same voltage and ampere-hour rating as the original batteries. Handle Used Batteries with Care! Assume that old batteries are fully charged. Use the same precautions you would use when handling a new battery. Do not short battery terminals or the battery string with a cable or tool when you disconnect the batteries! Batteries contain lead. Please dispose of old batteries properly. 23 114306E—Install/User <strong>Manual</strong>
CAUTION Do not dispose of batteries in a fire because the batteries could explode. Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes. It may be toxic. Dispose of Batteries Properly CAUTION Batteries contain lead. Many state and local governments have regulations about used battery disposal. Please dispose of the batteries properly. 24 114306E—Install/User <strong>Manual</strong>
Page 1 and 2: INSTALLATION & USER’S GUIDE 3kW -
Page 3 and 4: C A U T I O N READ ENTIRE MANUAL AN
Page 5 and 6: SECTION 9 Options………………
Page 7 and 8: BATTERY STORAGE WARNING This shipme
Page 9 and 10: Record Keeping An on-site permanent
Page 11 and 12: SECTION 3 BEFORE INSTALLING THE SYS
Page 13 and 14: Receiving and Moving the Unit and t
Page 15 and 16: SECTION 4 AC INPUT & AC OUTPUT INST
Page 17 and 18: Table 4.2 Recommended Minimum Wire
Page 19 and 20: SECTION 5 INSTALLING BATTERIES AND
Page 21 and 22: Before Installing the Batteries Too
Page 23: Connecting the Cables Between Batte
Page 27 and 28: BATTERY RETAINER BRACKET (TB1) INPU
Page 29 and 30: BRACKET BATTERY RETAINER DC FUSE (F
Page 31 and 32: SECTION 6 STARTUP AND SHUTDOWN PROC
Page 33 and 34: MAINTENANCE BYPASS PROCEDURE CAUTIO
Page 35 and 36: SECTION 8 FRONT PANEL DISPLAY The F
Page 37 and 38: Control Functions Control functions
Page 39 and 40: The Day of the Automatic Tests Tabl
Page 41 and 42: 3-PHASE SYSTEM: 1-POLE OUTPUT CIRCU
Page 43 and 44: REMOTE SUMMARY ALARM PANEL SCHEMATI
Page 45 and 46: SECTION 10 RS232 OPERATION 1.0 INTR
Page 47 and 48: 4.0 COMMANDS Meter Functions 4.1 Ge
Page 49 and 50: 4.7 Get Battery Current PC Interfac
Page 51 and 52: 5.8 Get Output Current Load Reducti
Page 53 and 54: 5.21 Get Alarm Log PC Interface: Sy
Page 55 and 56: LOCATION OF THE RS232 PORT RS232 po
Page 57 and 58: Fig. 10.5 56 114306E—Install/User
Page 59 and 60: SECTION 11 SPECIFICATIONS Input Out
Page 61 and 62: 60 THE NUMBER IN THE CHART INDICATE
Page 63 and 64: Heater Option Operation: The Heater
Page 65 and 66: SECTION 15 WARRANTY RETURN MATERIAL
Page 67: 66 114306E—Install/User Manual

Series CR Installation Manual PDF - Myers Power Products, Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?