Series CR Installation Manual PDF - Myers Power Products, Inc.

More documents

Recommendations

Info

SECTION 7 OPERATION The following is a description of the status LED's located on the front panel (Fig. 8.1). AC Present When the AC Mains is present, the LED will illuminate. If a power failure was long in duration, or the AC mains was disconnected by some other means (Circuit breaker open) the AC Present LED would not be illuminated. When the control circuit senses that the line has dropped below an acceptable level (Black Out, Brown Out, or Transient), the inverter will energize for at least one minute. So, if the power failure was a momentary glitch, the AC present LED would be illuminated but the inverter would be running. System Ready When the system has adequate battery voltage to transfer, the System Ready LED will illuminate. This feature prevents damage from multiple deep discharges of the battery. Battery Charging When the AC Mains is connected to the line and the battery is charging under normal conditions, the Battery Charging LED will illuminate. Battery Power When the inverter is producing output power (battery is being discharged), the Battery Power LED will be illuminated. Fault This is a summary Fault indication. When there is a fault condition present, the Fault LED will illuminate. To view which fault is present, use the keypad and LCD display feature. The front panel display will provide the user with a variety of information. It has a full compliment of Meter functions, Control functions and Program functions. 33 114306E—Install/User Manual
SECTION 8 FRONT PANEL DISPLAY The Front panel consists of a 2 x 20 alphanumeric LCD display with LED Back lighting, 5 Status LED indicators and a 4 x 4 keypad for user interface. Several parameters in the system software determine when and how your system conducts the automatic monthly and annual tests. Refer to “Program Functions” for a description of each test. Figure 8.1 Front Panel Display 34 114306E—Install/User Manual
Page 1 and 2: INSTALLATION & USER’S GUIDE 3kW -
Page 3 and 4: C A U T I O N READ ENTIRE MANUAL AN
Page 5 and 6: SECTION 9 Options………………
Page 7 and 8: BATTERY STORAGE WARNING This shipme
Page 9 and 10: Record Keeping An on-site permanent
Page 11 and 12: SECTION 3 BEFORE INSTALLING THE SYS
Page 13 and 14: Receiving and Moving the Unit and t
Page 15 and 16: SECTION 4 AC INPUT & AC OUTPUT INST
Page 17 and 18: Table 4.2 Recommended Minimum Wire
Page 19 and 20: SECTION 5 INSTALLING BATTERIES AND
Page 21 and 22: Before Installing the Batteries Too
Page 23 and 24: Connecting the Cables Between Batte
Page 25 and 26: CAUTION Do not dispose of batteries
Page 27 and 28: BATTERY RETAINER BRACKET (TB1) INPU
Page 29 and 30: BRACKET BATTERY RETAINER DC FUSE (F
Page 31 and 32: SECTION 6 STARTUP AND SHUTDOWN PROC
Page 33: MAINTENANCE BYPASS PROCEDURE CAUTIO
Page 37 and 38: Control Functions Control functions
Page 39 and 40: The Day of the Automatic Tests Tabl
Page 41 and 42: 3-PHASE SYSTEM: 1-POLE OUTPUT CIRCU
Page 43 and 44: REMOTE SUMMARY ALARM PANEL SCHEMATI
Page 45 and 46: SECTION 10 RS232 OPERATION 1.0 INTR
Page 47 and 48: 4.0 COMMANDS Meter Functions 4.1 Ge
Page 49 and 50: 4.7 Get Battery Current PC Interfac
Page 51 and 52: 5.8 Get Output Current Load Reducti
Page 53 and 54: 5.21 Get Alarm Log PC Interface: Sy
Page 55 and 56: LOCATION OF THE RS232 PORT RS232 po
Page 57 and 58: Fig. 10.5 56 114306E—Install/User
Page 59 and 60: SECTION 11 SPECIFICATIONS Input Out
Page 61 and 62: 60 THE NUMBER IN THE CHART INDICATE
Page 63 and 64: Heater Option Operation: The Heater
Page 65 and 66: SECTION 15 WARRANTY RETURN MATERIAL
Page 67: 66 114306E—Install/User Manual

Series CR Installation Manual PDF - Myers Power Products, Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?