DID 60 standard roller chain - Big Bike Webshop

adequate strength must be secured by adopting
corresponding dimensions.
3-3 Dimensions of fitting
Dimensions of general hardened fittings for
standard roller chains are listed below. For the
fittings of more than triple strand chains and
fittings of other shapes, please consult us. When
End fitting for simplex chain
designing an end fitting for any chain other than
standard roller chains, work out a safe design
based on sufficient understanding of this section. If
there is anything unclear, please consult us.
End fitting for duplex chain
Figure shows bushing press-fitted.
Dimensions of End fitting
Chain
No.
g W S D D' C r u H
Unit (mm)
(Reference) (Without Bushing) (With Bushing)
(Reference) (Reference) (Reference)
DID 35-1
DID 35-2
02.8 0.1
0
07.207.4
07.5 0
0.2
17.5 0
0.3
03.62 +0.05
0
05.02 0.02
10.1 0.1
4.5
4.7
09.0
DID 40-1
DID 40-2
03.2 0.1
0
10.911.1
11.2 0
0.2
25.4 0
0.3
04.00 +0.05
0
05.58 0.02
14.4 0.1
6.0
6.3
12.0
DID 50-1
DID 50-2
DID 60-1
DID 60-2
04.3 0.1
0
05.2 0.1
0
05.99 0.05
0 08.40 0.02
9.2
17.417.7 40.4 0
0.3
22.8 0.1
9.5
DID 80-1
07.97 0.1
11.27 0.02
12.2
0
24.2
DID 80-2 06.8 0.1
0 22.322.6 51.8 0
0.3
29.3 0.1
12.7
DID 100-1
27.5 0
0.3
09.57 0.1
13.47 0.02
15.2
0
30.2
DID 100-2 08.5 0.1
0 27.127.4 63.1 0
0.3
35.8 0.1
15.8
DID 120-1
35.5 0
0.3
11.15 0.1
15.64 0.02
18.2
0
36.2
DID 120-2 10.1 0.1
0 35.135.4 80.7 0
0.3
45.4 0.1
19.0
DID 140-1
37.2 0
0.3
12.75 0.1
17.94 0.02
21.2
0
42.3
DID 140-2 12.0 0.1
0 36.737.0 85.8 0
0.3
48.9 0.1
22.2
DID 160-1
45.2 0
0.3
14.33 0.1
19.94 0.02
24.2
0
48.3
DID 160-2 0 44.745.0 103.4 0
0.3
58.5 0.1
25.4
13.6 0.1
13.613.8
13.8 0
0.2
31.9 0
0.3
17.8 0
0.2
22.6 0
0.2
05.12 +0.05
0
07.16 0.02
18.1 0.1
Note:
1) The dimensions of D'can be applied only when DID bushings are used. If these dimensions are applied to the bushings for chains produced
by other manufacturers, the strength may be lower.
2) Dimensions "g" and "S" of duplex chain chain with bushings include the dimensions of the bushings.
7.5
7.9
15.0
18.1
7