Theta Controller User Manual

More documents

Recommendations

Info

User Manual Outputs OFF IN CYCLE DISASSEMBLY DETECTED CYCLE OK CYCLE NOK JOB SELECTED BIT READY Description The pin that is assigned as OFF means the output will do nothing when asserted. This is essentially a spare output. The size of this output function is 1 bit. This output asserts when the tool torque level, during the tightening cycle, exceeds the Threshold Torque value. It resets when the tool is shutoff either by reaching target, a fault, a Stop input, a Start input removed or by the operator. The size of this output function is 1 bit. Configuration: Contact Type Output Type This output asserts when Error Proofing is enabled and the accumulated count is greater than one and the tool mode is Disassembly and Threshold Torque is achieved. It resets when the tool lever or Start input is removed. The size of this output function is 1 bit. Configuration: Contact Type Output Type Asserts when a tightening cycle that exceeds the Threshold Torque is completed and the achieved torque and angle are audited within the limits of the audit step. Resets when the tool exceeds Threshold Torque on the next tightening cycle. The size of this output function is 1 bit. Configuration: Contact Type Output Type Asserts when a tightening cycle that exceeds the Threshold Torque is completed and the achieved torque and angle are audited outside the limits of the audit step. Resets when the tool exceeds Threshold Torque on the next tightening cycle. The size of this output function is 1 bit. Configuration: Contact Type Output Type Asserts or resets according to the binary value of the selected Job. This is one bit of a binary number created by several of these bits. The size of this output function is 1 bit. Configuration: Contact Type Bit: Bit defines the number you wish this bit to be in your binary number scheme of the selected job. Mode: All JOB SELECTED BITs must be the same mode, no mixing of modes allowed. Binary – Will create a decimal number equivalent to the weighted value of this binary bit(s). Binary + 1 – Will create a number equivalent to the weighted value of this binary bit(s) and add the value of one (1) to that number. Asserts when the controller is energized and there are no faults and there is nothing disabling the tool, such as Error Proofing or a Stop input. See section 2.2.6 for the conditions that can Stop Tool Operation. Resets when the controller is turned off or there is anything stopping the tool from operating. The size of this output function is 1 bit. Configuration: Contact Type Output Type 48
Theta Controller This page is blank Theta Controller Connections 49
Page 1 and 2: Assembly Technologies Theta Control
Page 3: Theta Controller 3.4.1 Display and
Page 6 and 7: User Manual Indicates an electrical
Page 8 and 9: User Manual 1.4 Installation Instru
Page 10 and 11: User Manual 1.4.1 Theta Controller
Page 12 and 13: 2.2.2 Dropdown 2.2.3 Menu Tree User
Page 14 and 15: User Manual Overcurrent Fault! Logi
Page 16 and 17: User Manual The left column shows t
Page 18 and 19: User Manual Wizard Screens Options
Page 20 and 21: User Manual 2.5.1.2 Setup: Job Tab
Page 22 and 23: User Manual 2.5.1.4 Setup: Step But
Page 24 and 25: User Manual Step Button Screens Opt
Page 26 and 27: 2.5.3 Setup Menu: 3. Other Other Sc
Page 28 and 29: Other Screens Options Screen User M
Page 30 and 31: Other Screens Options Screen User M
Page 32 and 33: 2.5.5 Service 2.5.5.1 Tool Tool Tab
Page 34 and 35: 2.5.6 Analyze Analyze Screens Optio
Page 36 and 37: User Manual Analyze Screens Options
Page 38 and 39: User Manual 3.2 Operator Protection
Page 40 and 41: User Manual Always ensure drive soc
Page 42 and 43: User Manual • Angle Cal (calibrat
Page 44 and 45: User Manual 3.5.5 Setting Torque, A
Page 46 and 47: 4.1.3 Theta Controller Serial Conne
Page 48 and 49: Outputs: Sourcing User Manual 44
Page 50 and 51: User Manual Outputs Description Con
Page 54 and 55: User Manual Glossary Abort Timer Ac
Page 56 and 57: User Manual Appendix A - Controller
Page 58 and 59: User Manual It has been found that
Page 60 and 61: User Manual Stanley shall not be re

Theta Controller User Manual

Create successful ePaper yourself

Delete template?

Save as template?