SanDisk SD Card

More documents

Recommendations

Info

Revision 2.2Chapter 2 – Product SpecificationsSanDisk SD Card Product ManualModel No.CapacitySDSDJ-1024SDSDH-1024SDSDX3-1024SDSDJ-2048SDSDH-20481024 MB1024 MB1024 MB2048 MB2048 MB© 2004 SanDisk Corporation 2-6 12/08/04
Revision 2.2Chapter 3 – SD Card Interface DescriptionSD Card Product Manual3 SD Card Interface Description3.1 General Description of Pins and RegistersThe SanDisk SD Card has nine exposed contacts on one side as shown in Figure 3-1. Thehost is connected to the card using a dedicated 9-pin connector.Table 3-1SD Card Pad AssignmentPin No. Name Type 1 DescriptionSD Mode1 CD/DAT3 2 I/O 3 , PP Card detect/Data line [Bit 3]2 CMD I/O, PP Command/Response3 V SS1 S Supply voltage ground4 V DD S Supply voltage5 CLK I Clock6 V SS2 S Supply voltage ground7 DAT0 I/O, PP Data line [Bit 0]8 DAT1 I/O, PP Data line [Bit 1]9 DAT2 I/O, PP Data line [Bit 2]SPI Mode1 CS I Chip Select (active low)2 DataIn I Host-to-card Commands and Data3 V SS1 S Supply voltage ground4 V DD S Supply voltage5 CLK I Clock6 V SS2 S Supply voltage ground7 DataOut O Card-to-host Data and Status8 RSV 4 --- Reserved9 RSV 5 --- Reserved1 Type Key: S=power supply; I=input; O=output using push-pull drivers; PP=I/O using push-pull drivers2 The extended DAT lines (DAT1-DAT3) are input on power up. They start to operate as DAT lines after theSET_BUS_WIDTH command. It is the responsibility of the host designer to connect external pullup resistors toall data lines even if only DAT0 is to be used. Otherwise, non-expected high current consumption may occur dueto the floating inputs of DAT1 & DAT2 (in case they are not used).3 After power up, this line is input with 50Kohm(+/-20Kohm) pull-up (can be used for card detection or SPI modeselection). The pull-up may be disconnected by the user, during regular data transfer, withSET_CLR_CARD_DETECT (ACMD42) command.4 The ‘RSV’ pins are floating inputs. It is the responsibility of the host designer to connect external pullup resistorsto those lines. Otherwise non-expected high current consumption may occur due to the floating inputs.5 Ibid.© 2004 SanDisk Corporation 3-1 12/08/04
Page 4 and 5: Revision 2.2SanDisk SD Card Product
Page 6 and 7: Revision 2.2Chapter 1 - Introductio
Page 16 and 17: Revision 2.2Chapter 2 - Product Spe
Page 18 and 19: Revision 2.2Chapter 2 - Product Spe
Page 22 and 23: Revision 2.2Chapter 3 - SD Card Int
Page 46 and 47: Revision 2.2Chapter 4 - SD Card Pro
Page 70 and 71:
Revision 2.2Chapter 4 - SD Card Pro
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Revision 2.2Chapter 5 - SPI Protoco
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Revision 2.2Appendix B -SanDisk Wor
Page 114 and 115:
Revision 2.2Appendix C -Limited War
Page 116 and 117:
Revision 2.2Appendix D -Disclaimer
Page 118 and 119:
Host Design Considerations:Applicat
Page 120 and 121:
Page 122 and 123:
show all

SanDisk SD Card

Create successful ePaper yourself

Delete template?

Save as template?