Operator's Manual

More documents

Recommendations

Info

LNC-M520iOP Panel Operation3.10 OT RELEASEOT REL is the short name of Over Travel RELease. There is one limit switch at end ofeach traveling side of servo axis in order to prevent to damage servo structure by colluding.When servo structure reaches traveling limit, over traveling will occur, which impliesemergency stop. When the screen has “EMERGENCY STOP OR OVER TRAVEL” andthis light is ON, please check whether or not the servo structure is over traveling.If it is over traveling, change the mode to MPG or JOG mode first. Then pressing this light(let this light ON), so the controller will ignore this over traveling emergency situationtemporarily. This implies that users can use hand wheel or axis-direction key to moveservo axis back to the travel range. Releasing (OT REL) button at this time in order to letthe system to continue travel checking.If everything is working normally, which means “CNC Ready” will replace “CNC Not Ready”,then continue operating. If other warning messages occur, please press [RESET] buttonbefore returning back to normal. Please be careful about moving direction, and movingspeed while moving the servo structure in order to prevent collusion.Note: It is possible that over traveling situation occurs when “NOT Ready” conditionoccurs without any prediction. Please put the over traveling condition into thechecking item when searching for reasons.122 LNC Technology Co., Ltd.
LNC-M520iOP Panel Operation3.11 COOLANT SUPPLYPressing this switch is to force coolant water to be ON. Pressing again is to force coolantwater to be off.LNC Technology Co., Ltd. 123
Page 3 and 4:
LNC-M520iTable of ContentTable of C
Page 5:
LNC-M520iTable of Content3.4 CYCLE
Page 8 and 9:
LNC-M520iGeneral1.1 Hardware Specif
Page 10 and 11:
LNC-M520iGeneral1.3 System Setting
Page 12 and 13:
LNC-M520iGeneralG Code G Code Funct
Page 14 and 15:
LNC-M520iCNC Operation2 CNC Operati
Page 16 and 17:
LNC-M520iCNC Operation(2)Sub-Functi
Page 18 and 19:
LNC-M520iCNC Operation(4)Character
Page 20 and 21:
LNC-M520iCNC Operation2.3 Screen an
Page 23 and 24:
LNC-M520iCNC Operation• PROG Func
Page 25 and 26:
LNC-M520iCNC Operation• CAM Funct
Page 27 and 28:
LNC-M520iCNC Operation• GRAPH Fun
Page 29 and 30:
LNC-M520iCNC Operation• SOFTPL Fu
Page 31 and 32:
LNC-M520iCNC Operation• PARAM Fun
Page 33 and 34:
LNC-M520iCNC Operation2.4.1 ABSOLUT
Page 35 and 36:
LNC-M520iCNC Operation2.4.3 MACHINE
Page 37 and 38:
LNC-M520iCNC OperationNote: Must co
Page 39 and 40:
LNC-M520iCNC Operation2.5 PROGPress
Page 41 and 42:
LNC-M520iCNC Operation• 【WORD F
Page 43 and 44:
LNC-M520iCNC OperationTo press “I
Page 45 and 46:
LNC-M520iCNC Operation• 【UNMARK
Page 47 and 48:
LNC-M520iCNC Operation2.5.2 BGPROG
Page 49 and 50:
LNC-M520iCNC OperationFigure 2.5-12
Page 51 and 52:
LNC-M520iCNC OperationIf the progra
Page 53 and 54:
LNC-M520iCNC Operation• 【DIR SE
Page 55 and 56:
LNC-M520iCNC Operation2.5.5 MDIPres
Page 57 and 58:
LNC-M520iCNC Operation• 【Comm.
Page 59 and 60:
LNC-M520iCNC Operation【SAVE AS】
Page 61 and 62:
LNC-M520iCNC Operation2.5.7 DNC Fun
Page 63 and 64:
LNC-M520iCNC Operation2.6.2 MACROPr
Page 65 and 66:
LNC-M520iCNC OperationSET X:Teachin
Page 67 and 68:
LNC-M520iCNC Operation2.7.3 CUT PAR
Page 69 and 70:
LNC-M520iCNC Operation2.7.4 Screen
Page 71 and 72:
LNC-M520iCNC Operation• CUT PARTh
Page 73 and 74:
LNC-M520iCNC Operation1. Figure sha
Page 75 and 76:
LNC-M520iCNC OperationLinearG73 Hig
Page 77 and 78: LNC-M520iCNC Operation3 rd Type: Si
Page 79 and 80: LNC-M520iCNC Operation2.8.4 Common
Page 81 and 82: LNC-M520iCNC Operation• PMNGThis
Page 83 and 84: LNC-M520iCNC Operation• G Code Se
Page 85 and 86: LNC-M520iCNC Operation2.9 GRAPH2.9.
Page 87 and 88: LNC-M520iCNC Operation• Drawing R
Page 89 and 90: LNC-M520iCNC Operation【WARM】War
Page 91 and 92: LNC-M520iCNC Operation2.10.2 IOCSA
Page 93 and 94: LNC-M520iCNC Operation2.10.4 SYSTEM
Page 95 and 96: LNC-M520iCNC Operation• 【H.D.
Page 97 and 98: LNC-M520iCNC Operation2.10.6 SYSUPD
Page 99 and 100: LNC-M520iCNC Operation• H.D CHECK
Page 101 and 102: LNC-M520iCNC Operation• PARAM LEA
Page 103 and 104: LNC-M520iCNC Operation• Text Font
Page 105 and 106: LNC-M520iCNC Operation【Max Error
Page 107 and 108: LNC-M520iCNC OperationThe Below Tab
Page 109 and 110: LNC-M520iCNC Operation2.12 PARAMPre
Page 111 and 112: LNC-M520iCNC Operation• 【MODIFY
Page 113 and 114: LNC-M520iCNC Operation2.12.2 USROPT
Page 115 and 116: LNC-M520iCNC Operation• Term auth
Page 117 and 118: LNC-M520iCNC Operation• Release T
Page 119 and 120: LNC-M520iOP Panel Operation3 OP Pan
Page 121 and 122: LNC-M520iOP Panel Operation3.4 CYCL
Page 123 and 124: LNC-M520iOP Panel Operation3.6 LED
Page 125 and 126: LNC-M520iOP Panel Operation(7)ZRNOp
Page 127: LNC-M520iOP Panel Operation3.9 SPIN
Page 131: LNC-M520iOP Panel Operation3.14 Add
show all

Operator's Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?