PA7300 Instruction Manual - TECO-Westinghouse Motor Company

More documents

Recommendations

Info

(29) PA-PID Card Relay 5 Control (Sn-34)(30) PA-PID Card Relay 6 Control (Sn-35)(31) PA-PID Card Relay 7 Control (Sn-36)(32) PA-PID Card Relay 8 Control (Sn-37)The PA-PID option card application parameters. Please refer to “PA-PID instructionmanual”.Used to control the pump ON/OFF.Sn-31 ~ 37=0Relay output invalid.Sn-31 ~ 37=1Relay output valid.(33) Parameter Copy (Sn-38)JNEP-32 LCD digital operator can upload the parameter settings from the digitaloperator to inverter and download parameter settings from the inverter to the digitaloperator.The digital operator will check its EEPROM or the inverter's EEPROM under thefollowing settings.Sn-38 = 0NO actionSn-38 = 1Upload data (digital operator inverter). During this period, the LED onthe digital operator will light sequentially in the CW sense.Sn-38 = 2Download data (inverter digital operator). During this period, the LEDon the digital operator will light sequentially in the CCW sense.Sn-38 = 3Verification check on digital operator’s EEPROM; during this period theLED will be switch-on between 2 groups.Please follow the below steps to implement the action of parameter copy betweendifferent inverters (either upload or download).Step 1Check the contents of digital operator EEPROM. (Sn-38='03'), then checkthe contents of inverter's EEPROM (Sn-38='04'). Make sure that bothEEPROM function properly.Step 2Download and copy the ' inverter's parameter settings to digital operatorEEPROM (Sn-38=2).Step 3Upload and copy the parameter settings of digital operator to other inverter'sEEPROM (Sn-38=1)104
2.5 Monitoring Parameters U n - ParameterNo.Un-01Un-02Un-03Un-04Un-05Un-06Un-07NameFrequency CommandOutput FrequencyOutput CurrentOutput VoltageMain Circuit DC VoltageOutput PowerOutput Power FactorLCD Display(English)Un-01=60.00HzFrequency CommandUn-02=60.00HzOutput FrequencyUn-03=12.5AOutput CurrentUn-04=220.0VOutput VoltageUn-05=310.0VDC VoltageUn-06= KWOutput PowerUn-07=0.90Output P.F.UnitDescriptions0.01HzDisplay frequency command, the displayedunit is determined by Cn-200.01HzDisplay output frequency, the displayed unitis determined by Cn-200.1A Display inverter output current0.1V Display output voltage command of inverter0.1V Display DC voltage of inverter main circuit0.1KW Display output power of inverter0.01 Display output power factor of inverterUn-08Input Terminal Status*2Un-08=00000000I/P Term. Status0 0 0 0 0 0 0 00OPEN1CLOSEInput terminal 1Input terminal 2Input terminal 3Input terminal 4Input terminal 5Input terminal 6Input terminal 7Input terminal 8Un-09Output Terminal Status*3Un-09=00000000O/P Term. Status0 0 0 0 0 0 0 00OPEN1CLOSERelay ContactR2A-R2COpto-contactD01-DCOMOpto-contactR1A-R1CReversedReversedReversedReversedReversedUn-10Un-11Un-12S/W Version<strong>Motor</strong> Elapsed RunHours<strong>Motor</strong> Elapsed EnergyKWHRUn-10=00001Software VersionUn-11=00001HrElapsed TimeUn-12=00001KwhElapsed Energy1Hr1KwhManufacturing useDisplay total time elapsed after pressingRUN (display data is resetable)*1Display total motor output energy (displaydata is resetable)*1105
Page 1 and 2:
4H358D0130001VARIABLE TORQUE INVERT
Page 3:
CAUTION AND WARNING:WARNINGDo not c
Page 6 and 7:
PART IINSTALLATION MANUAL4
Page 8 and 9:
2. RECEIVING!CAUTIONThis 7300PA has
Page 10 and 11:
3.2 LOCATIONLocation of the equipme
Page 12 and 13:
4.2 CONNECTION DIAGRAMThe following
Page 14:
Terminals GND Common lead for analo
Page 17 and 18:
(b) 440V SERIESMax. ApplicableMotor
Page 19 and 20:
(B) GROUNDING (PE: Protective Earth
Page 21 and 22:
6. MAINTENANCE6.1 PERIODIC INSPECTI
Page 23 and 24:
Table 6 Spare Parts for 440V ClassI
Page 25 and 26:
CHARACTERISTICSControl MethodFreque
Page 27 and 28:
(b) 220V30HP125HP440V40HP300HPWW1DW
Page 29 and 30:
9. PERIPHERAL AND OPTIONS9.1 AC REA
Page 31 and 32:
DRIVE FWD REVDIGITAL OPERATOR JNEP-
Page 33 and 34:
400 585A JUVPHV-0060 5 3H333C002023
Page 35 and 36:
9.4.2 ANALOG OPERATORAll 7300PA hav
Page 37 and 38:
PART IIOPERATION MANUAL33
Page 39 and 40:
Table 11 Key’s functionsKey Name
Page 41 and 42:
1.3 Parameter descriptionThe 7300PA
Page 43 and 44:
DescriptionKey SequenceDigital Oper
Page 45 and 46:
2.2 Parameters Can Be Changed durin
Page 47 and 48:
(1) Acceleration Time 1 (Bn-01)Acce
Page 49 and 50:
(16) Differential Time D (Bn-16) Ou
Page 51 and 52:
1. The PID sleep function is deacti
Page 53 and 54:
2.3 Control Parameters C n - Funct
Page 55 and 56:
FunctionEnergy-SavingTuningoperatio
Page 57 and 58: (5) DC braking current (Cn-11)Set D
Page 59 and 60: (13) Frequency agree detection leve
Page 61 and 62: OUTPUT FREQUENCYDECELERATION TIMEHY
Page 63 and 64: (25) Speed search detection level (
Page 65 and 66: (33) Energy-saving tuning operation
Page 67 and 68: (37) Auto Restart Time Interval (Cn
Page 69 and 70: FunctionOperationMode SelectProtect
Page 71 and 72: FunctionParameterNo.NameLCD Display
Page 73 and 74: Sn-XX = 1st digit2nd digit3rd digit
Page 75 and 76: (2) V/F Curve Selection (Sn-02)V/F
Page 77 and 78: (4) Operation Mode Select 1 (Sn-04)
Page 79 and 80: 3 Sn-04=10 XX Full-range DC injecti
Page 81 and 82: (6) Operation Mode Select 3 (Sn-06)
Page 83 and 84: 4th digit (operation select when fr
Page 85 and 86: 4th digit 3rd digit0 00 11 01 1Cont
Page 87 and 88: 3rd digit (operation continued at m
Page 89 and 90: (15) Multi-Function Contact Input S
Page 91 and 92: 1 FWD/REV run select (set value = 0
Page 93 and 94: 7 External baseblock (set value = 0
Page 95 and 96: 11 FJOG command, RJOG command (set
Page 97 and 98: 13 DC injection braking command (se
Page 99 and 100: (16) Multi-Function Analog Input Se
Page 101 and 102: (17) Multi-Function Contact Output
Page 103 and 104: 5 Frequency detection (set value=4)
Page 105 and 106: (18) Inverter station address (Sn-2
Page 107: (25) Pump Operation Mode Selection
Page 111 and 112: 2.6 Monitoring Parameters H n - Th
Page 113 and 114: 2.7 Order Parameters O n - Order p
Page 115 and 116: 3. FAULT DISPLAY AND TROUBLESHOOTIN
Page 117 and 118: Protection functionExplanationLCD d
Page 119 and 120: B.) Warning and Self-Diagnosis Func
Page 121 and 122: Protection functionExternal baseblo
Page 123 and 124: APPENDIXA. ENERGY-SAVING CONTROLa C
Page 125 and 126: B. PID CONTROLa Constants related t
Page 127 and 128: c How to adjustThe PID control func
Page 129 and 130: Reducing Long-cycle OscillationIf o
Page 131 and 132: (b) PA-P PROFIBUS protocol communic
Page 133 and 134: SOURCE MODE1 Internal power supply
Page 135 and 136: F. NOTES ON APPLICATION OF MOTORSMo
Page 137 and 138: H. CIRCUIT PROTECTION AND ENVIRONME
Page 139 and 140: I. INVERTER HEAT LOSS 220V CLASSInv
Page 141: K. CERTIFICATION FOR THE INVERTER C
show all

PA7300 Instruction Manual - TECO-Westinghouse Motor Company

Create successful ePaper yourself

Delete template?

Save as template?