ICPAGING Application User Manual - Barix

More documents

Recommendations

Info

Under the “AUDIO LEVELS” section input and output audio levels are displayed, in dB.3.4 ICCLIENT Web configuration pageAs in ICMASTER, the ICCLIENT application can be configured in a fast fashion. ClickingCONFIGURATION top menu button, a BASIC SETTINGS page will be displayed. All the applicationoptions are then available clicking the ADVANCED SETTINGS left-menu button.3.4.1 BASIC SETTINGSThe BASIC SETTINGS page is accessible clicking the CONFIGURATION button in the top menu, itshows the most important options to be set up for a quick configuration.Illustration 6: ICCLIENT <strong>Application</strong> “basic settings” Web Page• BARP Station ID• Duplex Mode• Use AI_Phone3.4.2 ADVANCED SETTINGSThe system ID of this client station. The ID is used to identify the unit at the masterstation.Default setting is "1".Choose the desired mode of operation. If “Half” is selected, the communication iscontrolled from the ICMASTER.Default setting is "Full".This setting is for Annuncicom 200 hardware only, which provides support for AIPHONE two wire interface. Set to "Yes" if AI_Phone is used as a door station. Inthis case “Half” operating mode is recommended.Default setting is "No".The ADVANCED SETTINGS page is accessible clicking the “Advanced Settings” button inthe left-side menu.22 Running ICCLIENT
Illustration 7: ICCLIENT <strong>Application</strong> “advanced settings” Web Page3.4.2.1 NetworkThis section is the same as in ICMASTER. See ICMASTER2.5.2.1 Network section.3.4.2.2 BARP Control• BARP Station IDThe system ID of this client station. The ID is used to identify the unit at the masterstation.Default setting is "1".• BARP Broadcast Address• BARP Audio Port• BARP Control Port• BARP Status PortBy default the ICCLIENT uses broadcast to listen/send on the BARP ports. Modifythe BARP IP address to use multicast if communication across different networksis desired, or if your LAN policy is not allowing broadcast.Default setting is "0.0.0.0".Enter the BARP port number where the ICCLIENT will listen for incoming audio.Default setting is "5555".Enter the BARP port number where the ICCLIENT will listen for BARP controlmessages.Default setting is "5556".Enter the destination port number to which the ICCLIENT will broadcast BARPstatus messages.Default setting is "5557".23 Running ICCLIENT
Page 1 and 2: ICPAGINGApplication User ManualICPA
Page 3 and 4: Table of Contents1 Introduction ...
Page 5 and 6: 8.1.1 DHCP ........................
Page 7 and 8: • till 8 configurable single or g
Page 9 and 10: jump to the corresponding part of t
Page 11 and 12: Illustration 1: ICMASTER keyboard l
Page 13 and 14: ICMASTER is in idle mode, pressing
Page 15 and 16: 2.5.2 ADVANCED SETTINGSIllustration
Page 17 and 18: • SNMP System Name2.5.2.2 BARP Co
Page 19 and 20: 2.5.2.4 Incoming Call• Call Maste
Page 21: 3 Running ICCLIENT3.1 About ICCLIEN
Page 25 and 26: • Min Paging Volume• Maximal BG
Page 27 and 28: • LED Status3.4.2.8 Security"alwa
Page 29 and 30: dark grey to white. The white point
Page 31 and 32: 5 Implementing example paging syste
Page 33 and 34: 5.3.3 ICMASTER settingsNow it is ti
Page 35 and 36: 5.5.3 Cash desk settings• BARP Co
Page 37 and 38: Click on “Create” and repeat al
Page 39 and 40: otherwise the unit will continue bo
Page 41 and 42: Decimal Binary Hexadecimal7 0111 78
Page 43 and 44: 8 Dictionary8.1.1 DHCPShort for Dyn
Page 45 and 46: 8.1.16 Network AddressThe host addr
Page 47: 9 Legal Information© 2012 Barix AG

ICPAGING Application User Manual - Barix

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?