1926-1984 Vintage Models - S&S Cycle

S e ction 5:Flathead Power ® by S&S ®Parts forTwin Cam 96 /103 2007-2012Parts forTwin Cam 88 ®1999-2006Parts forEvolution ®1984-1999S&S pushrod cover kits include all of the parts required for four pushrods, except keepers. Keepersare not included because of different length requirements of some engines, but are availableseparately. Pushrod covers and pushrod keepers are available for 1936-up big twin engines and1986-’90 Harley-Davidson® Sportster® models. Consult the chart below for the pushrod keepersyou require. Sold in kits of four assemblies; enough for one engine.Pushrod Cover KitsIncludes top and bottom covers, cover cap, cover spring, and spring washer for four pushrods.1979-’84 big twin engines (o-ring style bottom cover) ............... TÜV 3 93-4040KN-Series & 1936-'47 OHV big twin engines. .........................106-39491926-1984 Vintage ModelsPushrod Covers and Related REPLACEMENT Parts93-4040Parts forSportster ® & Buell ®1986-2012Parts forVintage Engines1926-1984Parts forX-Wedge®2007-2012Parts forVictory®, Off-road& MetricRacingProductsPERFORMANCEPARTSPushrod Cover PartsTop Cover 1966-up big twin (H-D® #17935-79B) .....USA USA 1,2,3TÜV 1,2,3,4,5,6,7 93-4016Top Cover KN-Series &1936-'47 OHV big twin (H-D® #17935-36). ..............106-3850Bottom Cover 1979-’84 big twin (H-D#17938-79) ....................... TÜV 393-4040Bottom Cover KN-Series & 1936-'47 OHV big twin (H-D® #17983-40) ...........106-3851Cover Cap 1936-up big twin, 1957-’90 Sportster® (H-D® #17945-36B).......................................USA USA 1,2,3TÜV 1,2,3,4,5,6,793-4017Cover Spring 1936-up big twin, 1957-’90 Sportster® (H-D® #17947-36)......................................USA USA 1,2,3TÜV 1,2,3,4,5,6,7 93-4018Cover Cap Washer (H-D® #6762B). .........................................50-7131Bottom Cover Washer (H-D#6737). .........................................50-7050Top O-ring (H-D® #11190, 11157, 11293). .....................................50-8039Middle O-ring (H-D® #11132A) ............................................50-8038Bottom O-ring (H-D#11145) ..............................................50-8037Quad Seal (H-D® #11133A) ............................................. 50-8064-SO-ring Square (H-D® #17955-36) ..........................................106-3849Pushrod O-ring Kits(For o-ring style bottom cover) Includes parts for four pushrods: top, middle, bottom o-rings.1979-’84 big twin models .....................................USA93-4041NOTE: Keepers and o-ring kits are available but must be purchased separately.93-4105Tools & ShopSuppliesDealer Services& Promo ItemsWarranty &Company PolicyOEM Cross ReferenceAppendix & Index5-60Pushrod KeepersAll S&S pushrod keepers are chromed steel, except part #93-4109. Keeper part #93-4109is intended for unusually tall engines. It is manufactured of unchromed stainless steel toprevent rust or peeling after it is trimmed to the required length.Keeper lengths for stock Harley-Davidson®engines are as follows:• 74" & 80" shovelhead – 3.330"• 74" panhead – 2.375"• 74" knucklehead – 3.312"• Ironhead Sportster® – 2.375"• Shovelheads -with S&S tappet guides – 2.900" (Subtract .430" from stock length)NOTE: All reference to H-D® part numbers is for identification purposes only. We in no wayare implying that any of S&S Cycle’s products are original equipment parts or that they areequivalent to the corresponding H-D® part number shown.Order toll free 866-244-2673S&S® Pushrod Cover Keeper Sets For1936-'99 Big Twins and harley-Davidson® Sportster® ModelsPart No.Length93-4070 2.400"93-4100 2.500" 900/1000cc + 1/8"93-4101 2.600"93-4115 2.800"93-4102 2.900"93-4103 3.000"93-4104 3.100"93-4105 3.200"93-4106 3.330" 74", KN74 , 80", 84", 86", 88", 93", KN9393-4107 3.500" 96",98"93-4108 3.625" 103"93-4109 4.250" Stainless steel may be cut to length.** Keepers are sold in sets of four.