Emulation Command Set Reference Manual - Hengstler GmbH

More documents

Recommendations

Info

XPM Emulation Command Set ReferenceESC [F0] [0F] [05] [w1] [w2] [h1] [h2] [a] – Bitmap header ................................................................ 89ESC [F0] [10] [04] [d1] [d2] [d3] [d4] – Presenter control command .................................................. 87ESC [F0] [10] [n] [d1]..[dn] – Bitmap body ......................................................................................... 90ESC [F0] [11] [0A] [n1]..[n2] [m1]..[m2] [i] [r] – Page Header ............................................................ 97ESC [F1] [01] [03] [0A] [n] - Page length setting ................................................................................ 28ESC [F1] [01] [04] [0D] [m] [n1] [n2] – Print correction offset ............................................................ 93ESC [F1] [01] [04] [0E] [m] [n1] [n2] – Mark cut correction offset ...................................................... 94ESC [F1] [05] [n] [m1] [mn] – Barcode scanner command ................................................................ 86ESC [F2] [01] [07] [d1]..[d7] - RS-232 communication parameter detting ......................................... 76ESC [F2] [03] [00] - Printer reset (hardware) ..................................................................................... 39ESC [F2] [04] [00] – Position stamp set ............................................................................................. 83ESC [F2] [05] [02] [n1] [n2] – Position stamp feed ............................................................................ 84ESC [F2] [06] [02] [n1] [n2] – Position stamp retract ......................................................................... 85ESC [FF] [2A] [n] [d1]..[dn] – Customer data upload ......................................................................... 91ESC [FF] [3A] [01] [n] – Customer data download ............................................................................ 92ESC ‘!’ [n] – Character size specification ........................................................................................... 18ESC ‘$’ [n1] [n2] [m1] [m2] – Set position .......................................................................................... 34ESC ‘%’ [n] - Character set and country code selection .................................................................... 16ESC ‘@’ - Printer reset (software) ..................................................................................................... 38ESC ‘^’ [n] – Print character 1-255 ..................................................................................................... 95ESC ‘-‘ [n] – Character underlining .................................................................................................... 25ESC ‘\’ [n1] [n2] – Print character 1-351 ............................................................................................ 96ESC ‘2’ – 1/6 inch line pitch setting ................................................................................................... 20ESC ‘3’ [n] - Line pitch setting ............................................................................................................ 21ESC ‘a’ [n] – Horizontal alignment setting ......................................................................................... 88ESC ‘A’ [n] - Line spacing setting ...................................................................................................... 22ESC ‘B’ [n] – Black-on-white reversed printing specification ............................................................. 19ESC ‘d’ [n] - Forward n-line feed ........................................................................................................ 33ESC ‘E‘ [n] – Bold character enable/disable ...................................................................................... 26ESC ‘V’ [n] [m] - Text, image and barcode rotation ........................................................................... 35ESC D [d1]..[dn] NUL - Horizontal tab positions ................................................................................ 31ESC J [n] - Forward paper feed ......................................................................................................... 32ESC SP [n] – Character spacing specification................................................................................... 24FF – Form feed .................................................................................................................................. 15FS ‘r’ [n] –Set status parameter ......................................................................................................... 72GS ‘’’ [m] [n] - Print stored image data ............................................................................................... 40GS ‘e’ [n] [m] - Bar code bar width setting ......................................................................................... 41GS ‘h’ [n] - Bar code height setting .................................................................................................... 42GS ‘k’ [m] [n] [d1]..[dn] - Bar code printing ........................................................................................ 44GS ‘L’ [n] [m] - Left margin specification ............................................................................................ 23GS ‘w’ [n] - Bar code width magnification setting .............................................................................. 43HT – Horizontal tab ............................................................................................................................ 12LF – Line feed .................................................................................................................................... 13Feeder StatusFeeder Status Summary .................................................................................................................... 63Part No. D 690 004 Page 108 of 112 Mod.Nr. 4 240512 HOR1
XPM Emulation Command Set ReferenceFirmwareReleased firmware versions ................................................................................................................ 4Graphic PrintingPrint RLE 8 compressed graphics ..................................................................................................... 74Print uncompressed graphics ............................................................................................................ 73Repeat graphics line .......................................................................................................................... 75Set position ........................................................................................................................................ 34ImagesEnd block rotation .............................................................................................................................. 37Image rotation .................................................................................................................................... 35Print stored image data ...................................................................................................................... 40Start block rotation ............................................................................................................................. 36Mark ControlMark cut correction offset................................................................................................................... 94Paper ControlCarriage Return ................................................................................................................................. 14Cutter Control ..................................................................................................................................... 29End of Form ....................................................................................................................................... 29End of Page ....................................................................................................................................... 29End of Print ........................................................................................................................................ 29Form feed ........................................................................................................................................... 15Forward n-line feed ............................................................................................................................ 33Forward paper feed ...................................................................................................................... 32, 81Horizontal tab ..................................................................................................................................... 12Line feed ............................................................................................................................................ 13Page Header ...................................................................................................................................... 97Page length setting ............................................................................................................................ 28Paper path control .............................................................................................................................. 80Position stamp feed ........................................................................................................................... 84Position stamp retract ........................................................................................................................ 85Position stamp set .............................................................................................................................. 83Print speed setting ............................................................................................................................. 79Printout cancellation request ............................................................................................................. 82Top of Form ....................................................................................................................................... 29Top of Page ....................................................................................................................................... 29Presentercontrol command ............................................................................................................................... 87Presenter StatusPresenter Status Summary ................................................................................................................ 65Printer Data PacketBarcode Data Packet ([1B] [FF] [07] [m] [d1]..[dn]) ........................................................................... 64Feeder Status Packet ([1B] [FF] [06] [m] [d1]..[dn])........................................................................... 63Flash Info Packet ([1B] [FF] [05] [m] [d1]..[dn]).................................................................................. 61Life Data Packet ([1B] [FF] [09] [m] [d1]..[dn]) ................................................................................... 67Part No. D 690 004 Page 109 of 112 Mod.Nr. 4 240512 HOR1
Page 8 and 9:
XPM Emulation Command Set Reference
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59: XPM Emulation Command Set Reference
Page 112: XPM Emulation Command Set Reference
show all

Emulation Command Set Reference Manual - Hengstler GmbH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?