FILARC flux - Esab

More documents

Recommendations

Info

FILARC flux- andmetal- coredwelding wiresFFILARC PZ6114SAWS A5.20-95 : E71T-1J H4EN 758-97 : T 46 4 P C 1 H5Contents page 4Welding parametersPrevious pageNext pageDESCRIPTIONAll-position rutile cored wire providing C : 0.04-0.08% P : ≤0.020%DEPOSITION DATA IN: CO 2good CVN toughness down to -40°C. Si : 0.30-0.50% S : ≤0.020%Developed for use in CO 2 shielding gas.The combination of reliable mechanicalMn: 1.10-1.50%Ni : 0.25-0.50%properties and high productivity makethis wire suitable for semi-automatic,mechanised and robotic welding.SHIELDING GASWelders appreciate the characteristicsoft, spatter-free spray arc at all currents.CO 2A single parameter setting can be EN 439: C1applied to cover all welding positions,(Ø1.2mm/230A). Deposition rates up to4-5kg/h can be reached in PF position. WELD METAL HYDROGENSlag is always easily detachable, leavingwelds with good tie-in and a nice Euronorm 758-95: class H5bead appearance. High quality, onesidedroot runs are deposited very Typical value in CO 2: 3.7ml/100geconomically on ceramic backing.A versatile and productive wire forgeneral fabrication and shipbuilding.Diameter1.2mmStickout20mmI V wire Dep. rate[A] [m/min] [kg/h]150 5.6 2.1250 11.1 4.2350 19.8 7.5ALL WELD METAL MECHANICAL PROPERTIESDiameter1.4mmStickout20mmI V wire Dep. rate[A] [m/min] [kg/h]150 3.3 1.8250 6.6 3.6350 11.6 6.3450 18.9 9.4WELD METAL COMPOSITIONAPPROVALSsee pages13 to17for gradesABSBVCCSCRSDBDNVFORCEGLLRMRSPRSTÜVUDTPOSITIONSCURRENTANDPOLARITYDC +Tensile strength, R m [MPa]: 540-640Yield strength, R e[MPa]: ≥420Elongation, A 5 [%] : ≥22Impact value, A v (ISO-V) – 20°C [J] : ≥70–40°C [J] : ≥47CERAMICBACKING42
FILARC flux- andmetal- coredwelding wiresTypical one-sided welding procedures for hull construction, using FILARC PZ6114(S)and PZ6130HS (see next chapter) cored wires.Hull block unitSteel: HT EHA Vertical-up position, using FILARC PZ 6114(mixed gas) or PZ 6114S (CO 2 ) rutile fluxcoredwires, continuously weaved. Weldingparameters are valid for mixed gas.Increase arc voltage by 1-2V for CO 2 .CeramicbackingContents page 416mmPrevious pageNext pageRoot, welding current : 200Awelding voltage : 23VFill, welding current : 230Awelding voltage : 26VB Downhand position, root pass with FILARC basic flux-cored wire PZ 6130HS, 1.6mm in CO 2 gasCeramicbackingRetention platewith magnets15 or16mmWire size : 1.6mmWelding current : 220-240AWelding voltage : 24-26VWire stickout : 20mmGas : CO 2Welding speed : 40-45cm/minfor averageroot gapC Horizontal-vertical position, all passes with FILARC basic flux-cored wire PZ 6130HS, 1.6mm in CO 2 gasor mixed gas. Decrease arc voltage by 1-2V for mixed gas.Narrowroot gapwith singlepass weldWideroot gapbuilt upwith threepassesPlate thickness : 16mmWire size : 1.6mmWelding current : root 190 to 250AWelding voltage : root 24V to 26VWire stickout : 15-18mmGas : CO 2Welding speed : 25-30cm/minfor average root gap43
Page 1 and 2: FILARC flux- andmetal- coredwelding
Page 43: FILARC flux- andmetal- coredwelding
Page 95 and 96:
FILARC flux- andmetal- coredwelding
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
show all

FILARC flux - Esab

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?