Quick Reference for End-Users CarboSen1000 Sensors ... - lamtec

More documents

Recommendations

Info

3 Technical Description3.3 Sensor Electronics XC 164The microprocessor-controlled sensor electronics perform the following functions in the system:• Heating the sensor and regulating the heater spiral to a constant heating resistance• Acquisition of the sensor voltages in mV• Conversion of measured sensor voltages and output to the analogue output (0/4-20mA)• Monitoring of both sensor voltages• Checking the analogue outputs• Output of measured values on USB CAN bus.The electronics have a power supply of 13V to 30V DC. Ideally with 24V / 1.5A.The standard configuration CO e is calculated from the sensor voltage and would be given inthe analogue output. Internally, both sensor signals are compared and checked on the basisof the following failure criteria (standard parameterisation):• Difference greater than 25mV, or• Difference greater than 25% from the current measured value.Fig. 3-5 Electronics with adapter housingFig. 3-6 Electronics for top hat rail mounting11
4 Installation and Commissioning4 Installation and Commissioning4.1 General InformationMeasuring temperature:Type NT and clip housing 150°CType HT: 150°.... 400°CPerformance and average lifespan for the following fuel:Blue flame burner (oil / gas):approx. 3 yearsWood combustion (neat stock wood / pellets): approx. 2 yearsOther fuel for wood combustion, according to < 1 yearcontamination concentration (e.g. woodchip, bark)Measuring point:The measuring point should have the complete mixture of representativeexhaust gasesMounting position:The mounting position of the sensor should be as perpendicularas possible to the connection cable or the connection head, atleast 10° over the horizontal level.4.2 Installation4.2.1 CarboSen1.000STThe sensor system with CarboSen1000 ST electronics is set up and connected as describedin the following steps:• Connect the 4-pin plug (power supply (13V-30V) / analogue output). Make sure that thepower supply is switched off. Connection cable schielded, max. cable cross section 1mm 2 .The maximum cable length of 100m should not be exceeded.• If required, connect to LAMTEC SYSTEM BUS 5-pin, for connection of LSB-Modules and/or programming unit. Connection cable schielded, max. cable cross section 1mm 2 .The maximum cable length of 100m should not be exceeded.• After the plug has been connected, the power supply can be switched on.First, the sensor is heated to operating temperature. This process is complete when only thegreen LED is continuously lit. This cold start phase then lasts approximately 2min.Plug A1Round plug connector, 4-pin• Pin 1 Supply voltage 0V• Pin 2 Supply voltage 24VDC• Pin 3 Analogue output -• Pin 4 Analogue output +12
Page 4 and 5: Table of Contents6 OPERATION . . .
Page 6 and 7: 1 General Information1 General Info
Page 8 and 9: 2 Safety2.2 For Your SafetyIn this
Page 10 and 11: 3 Technical Description3 Technical
Page 14 and 15: 4 Installation and CommissioningPlu
Page 16 and 17: 4 Installation and Commissioning4.3
Page 18 and 19: 5 Menu5 Menu5.1 Switching on the Op
Page 20 and 21: 5 Menu5.2.1 Help WindowTo switch to
Page 22 and 23: 5 Menu5.3.4 Control ValuesPlease us
Page 24 and 25: 5 Menu5.3.6 COe CurvesPlease use th
Page 26 and 27: 5 Menu5.3.7 LSB Configuration25
Page 28 and 29: 5 MenuNOTICE!You can upload import
Page 30 and 31: 6 Operation6.2.3 Performing Sensor
Page 32 and 33: 6 Operation6.2.5 Initiate the Cold
Page 34 and 35: 6 Operation6.2.6 Changing the Senso
Page 36 and 37: 6 Operation6.2.8 Setting the Limit
Page 38 and 39: 8 Accessories8 Accessories8.1 Progr
Page 40 and 41: 8 Accessories8.4 Digital Input Modu
Page 42 and 43: 9 Technical Data9 Technical DataEle
Page 44 and 45: 10 Ordering Information10 Ordering
Page 46 and 47: 11 FAQbasic principle, the lower th
Page 48 and 49: 12 Error Detection and Measurements
Page 50 and 51: 14 Declaration of Conformity14 Decl
Page 52: 14 Declaration of Conformity51

Quick Reference for End-Users CarboSen1000 Sensors ... - lamtec

Create successful ePaper yourself

Delete template?

Save as template?