Quick Reference for End-Users CarboSen1000 Sensors ... - lamtec

More documents

Recommendations

Info

8 Accessories8.4 Digital Input Module with module address 11• 4 digital inputs 24V/DCThe inputs are executed with an input voltage of 24V/DCwith electrical isolation.Item no. 663 R 4028• Input 1 – RESET limit values 1 & 2Input 2 – not assignedInput 3 – start sensor testInput 4 – RESET fault / warning• Manually operated emergency menuSetting „1“ Input is HIGH at all timesSetting „A“ Input switches over contact from outsideSetting „0“ Input is LOW at all timesFig. 8-5 digital input moduleNOTICE!The input and output module can be mounted without any gap. After mounting 15 modules,the power supply should start externally.With more than 15 modules, the bypass plug would be overloaded and burn out.Please observe the fuse protection of the external power supply. Bear in mind that there is noline-side fuse available.NOTICE!Please check the accuracy of the preset module address!8.5 Power PackExt. power pack 230VAC/24VDC - 1.5A (35W) <strong>for</strong> power supply of <strong>CarboSen1000</strong> ST, the programmingunit and the module• Item no. 658 R 01095• Range of input voltage 85...264 VAC, 47...63 Hz• Typical current consumption 0.48A• Installing on mounting rail TS35• Operational temperature range -20...+60°C• Weight 270gr• Protection class IP 2039
8 AccessoriesFig. 8-6 Ext. Power Pack 230VAC/24VDC – 1,5A (35W) Type 658 R 01095Fig. 8-7 Dimensional diagram ext. Power Pack Type 658 R 0109540
Page 4 and 5: Table of Contents6 OPERATION . . .
Page 6 and 7: 1 General Information1 General Info
Page 8 and 9: 2 Safety2.2 For Your SafetyIn this
Page 10 and 11: 3 Technical Description3 Technical
Page 12 and 13: 3 Technical Description3.3 Sensor E
Page 14 and 15: 4 Installation and CommissioningPlu
Page 16 and 17: 4 Installation and Commissioning4.3
Page 18 and 19: 5 Menu5 Menu5.1 Switching on the Op
Page 20 and 21: 5 Menu5.2.1 Help WindowTo switch to
Page 22 and 23: 5 Menu5.3.4 Control ValuesPlease us
Page 24 and 25: 5 Menu5.3.6 COe CurvesPlease use th
Page 26 and 27: 5 Menu5.3.7 LSB Configuration25
Page 28 and 29: 5 MenuNOTICE!You can upload import
Page 30 and 31: 6 Operation6.2.3 Performing Sensor
Page 32 and 33: 6 Operation6.2.5 Initiate the Cold
Page 34 and 35: 6 Operation6.2.6 Changing the Senso
Page 36 and 37: 6 Operation6.2.8 Setting the Limit
Page 38 and 39: 8 Accessories8 Accessories8.1 Progr
Page 42 and 43: 9 Technical Data9 Technical DataEle
Page 44 and 45: 10 Ordering Information10 Ordering
Page 46 and 47: 11 FAQbasic principle, the lower th
Page 48 and 49: 12 Error Detection and Measurements
Page 50 and 51: 14 Declaration of Conformity14 Decl
Page 52: 14 Declaration of Conformity51

Quick Reference for End-Users CarboSen1000 Sensors ... - lamtec

Create successful ePaper yourself

Delete template?

Save as template?