Quick Reference for End-Users CarboSen1000 Sensors ... - lamtec

More documents

Recommendations

Info

6 Operation6.2.6 Changing the Sensor Temperature (RI)You need release level 2 to do these settings.Insert your password for release level 2. You will getthis password after consulting with LAMTEC support.Phone: +49 (0) 6227 6052 33E-mail: support@lamtec.dethe bigger the factor the higher the temperaturethe smaller the factor the lower the temperatureThe steps for changing the factor may have amaximum of 0,1.Mind the following limit!Never exceed the maximum factor of 2,8.If you exceed the maximum this may disturbthe sensor or minimises it’s lifetime enormusly.If the factor is smaller than 2,4, the sensor istoo cold. This may lead to a false measurementand to a too high offset.Change with key into the main menu and start the installation (refer to chapter 6.2.5 Initiatethe Cold Resistance Determination).33
6 Operation6.2.7 Analogue Output 1You need release level 1 to do these settings.Insert the password for release level 1.If you have forgottenyour password, contact LAMTEC support.Phone: +49 (0) 6227 6052 33E-mail: support@lamtec.deIn analogue output 1 choose, which value analogueoutput 1 shall output.Meas. Usen = average sensor voltageMeas. Usen 1 = single voltage, for calculating the averagesensor voltageMeas. Usen 2 = single voltage, for calculating the averagesensor voltageHeating power = the heater’s wattageR-Heater = the heater’s resistancePulse-width = the heater’s pulse-widthRki = ceramic inner resistanceCOe = calculated CO e value of the preset characteristiccurve34
Page 4 and 5: Table of Contents6 OPERATION . . .
Page 6 and 7: 1 General Information1 General Info
Page 8 and 9: 2 Safety2.2 For Your SafetyIn this
Page 10 and 11: 3 Technical Description3 Technical
Page 12 and 13: 3 Technical Description3.3 Sensor E
Page 14 and 15: 4 Installation and CommissioningPlu
Page 16 and 17: 4 Installation and Commissioning4.3
Page 18 and 19: 5 Menu5 Menu5.1 Switching on the Op
Page 20 and 21: 5 Menu5.2.1 Help WindowTo switch to
Page 22 and 23: 5 Menu5.3.4 Control ValuesPlease us
Page 24 and 25: 5 Menu5.3.6 COe CurvesPlease use th
Page 26 and 27: 5 Menu5.3.7 LSB Configuration25
Page 28 and 29: 5 MenuNOTICE!You can upload import
Page 30 and 31: 6 Operation6.2.3 Performing Sensor
Page 32 and 33: 6 Operation6.2.5 Initiate the Cold
Page 36 and 37: 6 Operation6.2.8 Setting the Limit
Page 38 and 39: 8 Accessories8 Accessories8.1 Progr
Page 40 and 41: 8 Accessories8.4 Digital Input Modu
Page 42 and 43: 9 Technical Data9 Technical DataEle
Page 44 and 45: 10 Ordering Information10 Ordering
Page 46 and 47: 11 FAQbasic principle, the lower th
Page 48 and 49: 12 Error Detection and Measurements
Page 50 and 51: 14 Declaration of Conformity14 Decl
Page 52: 14 Declaration of Conformity51

Quick Reference for End-Users CarboSen1000 Sensors ... - lamtec

Create successful ePaper yourself

Delete template?

Save as template?