Quick Reference for End-Users CarboSen1000 Sensors ... - lamtec

More documents

Recommendations

Info

12 Error Detection and Measurements12.5 FaultsNo. Output text Cause of fault signal Remarks1 Heater defect maximum heating power is exceeded would be restrained during the heatingphase2 Heater defect Connection to other channels aborted(timeout expired)3 Analogue output defect an error occur during initialisation ofthe analogue output4 Sensor voltage beyondthe limits5 U sen difference toohigh12.6 Warningsone OR both sensor voltages beyond-30 to 700mVmaximum allowable voltage differencebetween the electrodes is exceeded.sensor may be fine but the control isnot workingno measurement value from analogueoutputnot implemented yetwould be restrained during the heatingphase; warning when it is 1-channel,fault message when it is 2-channelsNo. Output text Cause of fault signal Remarks101 Ph max achieved maximum heating power is exceeded would be restrained during the heatingphasePh min achieved, overheatedambience103 Heating resistancebeyond the limits104 U sen difference toohigh105 Ceramic resistancebeyond the limits106 Deviation of R h fromsetpoint value107 Sensor resistancedriftsfalling below minimum heating powerfixed cold resistance falls beyond specificlimitsmaximum allowable voltage differencebetween the electrodes is exceededfixed ceramic resistance falls beyondspecific limitsthe current measured value R h deviatestoo far away from the saved setpointvaluethe resistance values changes significantly(measured over a long period oftime)would be restrained during the heatingphaseSensor would be operated with defaultvalue R kaltwould be restrained during the heatingphase; warning when it is 1-channel,fault message when it is 2-channelsSensor would be operated with defaultvalue R kalt(only with R ki -Control)long-run testing of the discarded triple(R h ,R ki ,U s ), Triple would be relocatedback after every installation routine.47
13 Support13 SupportLAMTEC Mess- und Regeltechnik für Feuerungen GmbH & Co. KGWiesenstraße 669190 Walldorfsupport@<strong>lamtec</strong>.deTel.: +49 6227 – 6052-33 Fax: +49 6227 – 6052-5748
Page 4 and 5: Table of Contents6 OPERATION . . .
Page 6 and 7: 1 General Information1 General Info
Page 8 and 9: 2 Safety2.2 For Your SafetyIn this
Page 10 and 11: 3 Technical Description3 Technical
Page 12 and 13: 3 Technical Description3.3 Sensor E
Page 14 and 15: 4 Installation and CommissioningPlu
Page 16 and 17: 4 Installation and Commissioning4.3
Page 18 and 19: 5 Menu5 Menu5.1 Switching on the Op
Page 20 and 21: 5 Menu5.2.1 Help WindowTo switch to
Page 22 and 23: 5 Menu5.3.4 Control ValuesPlease us
Page 24 and 25: 5 Menu5.3.6 COe CurvesPlease use th
Page 26 and 27: 5 Menu5.3.7 LSB Configuration25
Page 28 and 29: 5 MenuNOTICE!You can upload import
Page 30 and 31: 6 Operation6.2.3 Performing Sensor
Page 32 and 33: 6 Operation6.2.5 Initiate the Cold
Page 34 and 35: 6 Operation6.2.6 Changing the Senso
Page 36 and 37: 6 Operation6.2.8 Setting the Limit
Page 38 and 39: 8 Accessories8 Accessories8.1 Progr
Page 40 and 41: 8 Accessories8.4 Digital Input Modu
Page 42 and 43: 9 Technical Data9 Technical DataEle
Page 44 and 45: 10 Ordering Information10 Ordering
Page 46 and 47: 11 FAQbasic principle, the lower th
Page 50 and 51: 14 Declaration of Conformity14 Decl
Page 52: 14 Declaration of Conformity51

Quick Reference for End-Users CarboSen1000 Sensors ... - lamtec

Create successful ePaper yourself

Delete template?

Save as template?