CH-TRAMPAC - Waste Isolation Pilot Plant - U.S. Department of ...

More documents

Recommendations

Info

CH-TRAMPAC Document Rev. 2, May 2005Table 2.3-3 – HalfPACT and Payload Assembly Maximum Gross WeightLimitsPayloadMaximum Gross Weight(pounds)Payload (Contents) 7,600Loaded HalfPACT (Package) 18,100Maximum gross weight limits for payload assemblies of either the TRUPACT-II or HalfPACTinclude the weight of the loaded payload container(s) and any additional payload assembly items(e.g., pallets, spacers, guide tubes, slip sheets, reinforcing plates, banding material, slings, etc., asspecified in Section 2.9). Actual payload assembly weights are limited by “as-built”TRUPACT-II and HalfPACT weights and U.S. Department of Transportation requirements for aloaded transport vehicle.Payload containers and TRUPACT-II or HalfPACT payloads shall be acceptable for transportonly if the weight plus the measurement error (i.e., one standard deviation) is less than or equalto the maximum gross weights specified in Table 2.3-1 and Table 2.3-2 or Table 2.3-3.2.3.1.2 Requirements for Center of GravityFor TRUPACT-II payloads, the total weight of payload container(s) in the top layer of thepayload assembly shall be less than or equal to the total weight of payload container(s) in thebottom layer of payload assembly. In the case of drums overpacked in a TDOP, the total weightof the top layer of drums shall be less than or equal to the total weight of the bottom layer ofdrums.No center of gravity requirements exist for HalfPACT payloads.2.3.2 Methods of Compliance and Verification2.3.2.1 Methods of Compliance and Verification for Container/Assembly WeightCompliance shall be by measurement. The weight of each payload container (or dunnage) shallbe determined using a calibrated scale. The scale calibrations shall be in accordance with theNational Institute of Standards and Technology Handbook 44 1 , or an equivalent standard. Theweight and the measurement error (i.e., one standard deviation) of each payload container shallbe recorded in the Payload Container Transportation Certification Document (PCTCD) or theOverpack Payload Container Transportation Certification Document (OPCTCD), as appropriate(see Section 6.2.1).1 National Institute of Standards and Technology, Specifications, Tolerances, and Other Technical Requirements forWeighing and Measuring Devices, NIST Handbook 44, National Institute of Standards and Technology, Office ofWeights and Measures, Washington, D.C.2.3-2
CH-TRAMPAC Document Rev. 2, May 2005One of two methods shall be used to calculate the total weight of the payload:• If the total payload gross weight is obtained by summing the weights of the individualpayload containers or dunnage, it shall include the square root of the sum of the squaresof the individual measurement errors. If used, the weight of pallets, reinforcing plates,slip sheets, guide tubes, stretch wrap, adjustable slings, etc., shall be added to the sum ofthe weights of the individual payload containers.• If the total payload gross weight is obtained by weighing the payload as an assembly, themeasurement shall include the error.The weight and the measurement error shall be reported on the Payload Assembly TransportationCertification Document (PATCD) (see Section 6.2.2).2.3.2.2 Methods of Compliance and Verification for Center of GravityThe weight and measurement error of each payload container and of the total payload shall becalculated and reported on the PATCD (see Section 6.2.2), which requires the documentation ofverification of compliance with the center of gravity requirements for TRUPACT-II payloads.No center of gravity requirements exist for HalfPACT payloads.2.3-3
Page 5 and 6: CH-TRAMPAC Document Rev. 2, May 200
Page 26: CH-TRAMPAC Document Rev. 2, May 200
Page 39: CH-TRAMPAC Document Rev. 2, May 200
Page 91 and 92:
CH-TRAMPAC Document Rev. 2, May 200
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
show all

CH-TRAMPAC - Waste Isolation Pilot Plant - U.S. Department of ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?