CIMCO

More documents

Recommendations

Info

14Snap to Grid snaps to the grid points.Snap to Points snaps to points drawn by the user.Snap to Center Points snaps to the centers of circles and arcs.Snap to Mid points snaps to the midpoints of elements.Snap to Mid points snaps to the midpoints of elements.Snap to Intersections snaps to the intersections between elements.Enable All Snap Types activates all snap types.Disable All Snap Types deactivates all snap types.Setup CNC-Calc lets you access the configuration for CNC-Calc.7.2.Points and LinesThe Points/Lines toolbar contains functions for drawing lines andpoints defined in different ways. The functions in this toolbar can befound under Draw Points/Lines in the menu.Setup CNC-Calc lets you access the configuration for CNC-Calc.Between 2 Points will draw a line between two selected points.Vertical will draw a vertical line. The first point selected definesthe starting point (and the X coordinate), the second point selecteddefines the length (and need not be directly above or below the firstpoint).
15Horizontal will draw a horizontal line. The first point selecteddefines the starting point (and the Y coordinate), the second pointselected defines the length (and need not be directly to the left orright of the first point).Polar lets you select the starting point of a line, and you then select(or write) the angle and length of the line.Perpendicular draws a line perpendicular to another line. You firstselect the line your new line is to be perpendicular to, then thestarting point of your new line. You then select the length of yournew line, and last you select in which direction from the startingpoint your new line is to go.Parallel draws a line parallel to another line. You first select the lineyour new line is to be parallel to, then the starting point of your newline. You then select the length of your new line, and last you selectin which direction from the starting point your new line is to go.Bisector draws a line bisecting two other lines, i.e. a line that halvesthe angle between two lines. You first select the two lines you wantto bisect, then you select the length of your new line (from theintersection of the two lines you are bisecting), and last you selectwhich of the four possible solutions you want to keep.Tangent Two Elements lets you draw a line tangent to two circles orarcs. You select the two circles or arcs your new line is to be tangentto, and then you select which of the solutions you want to keep.Tangent Angle draws a line tangent to an arc or circle, at a selectedangle. You first select the arc or circle your new line is to be tangentto, then the angle and length, and last you select which of the twosolutions you want to keep.Tangent Through Point draws a line tangent to an arc or circle, to aselected point. You first select the arc or circle your new line is to betangent to, then the point it is to go though, and last you select whichof the two solutions you want to keep.
Page 3: 3CIMCO CNC-Calc 2.5 User Guide© 19
Page 6: 6Notice:The accompanying software i
Page 9 and 10: 94.InstallationCNC-Calc v2 is insta
Page 11 and 12: Most of the functions in CNC-Calc v
Page 13: 137.7.1.ToolbarsToolThe Tools toolb
Page 17 and 18: 17Tangent through Point lets you de
Page 19 and 20: 197.5.ModifyThe Modify toolbar modi
Page 21 and 22: 21Pocket Milling creates pocket ope
Page 23 and 24: 238.MenusMost of the CNC-Calc v2 fu
Page 25 and 26: 25Tangent AngleTangent Through Poin
Page 27 and 28: 27Simple Text Circular AlignmentTru
Page 29 and 30: 29Ctrl- Backspace.Zoom inZoom outZo
Page 31 and 32: 31Export ContourCalculatorCan expor
Page 33 and 34: 33It is important to select the cor
Page 35 and 36: 35Rotary axisIf Y-axis substitution
Page 37 and 38: 3711. Other configurations thataffe
Page 39 and 40: 3912.1.Before you startThe first th
Page 41 and 42: 4112.1.Draw the geometryDraw a rect
Page 43 and 44: 43Offset a circleClick onin the too
Page 45 and 46: 45Mirror elements about mirror line
Page 48 and 49: 4813. Tutorial 2CNC-toolpaths and F
Page 50 and 51: 50You should now see the part from
Page 52 and 53: 52Retract Height: When the operatio
Page 54 and 55: 54In order to use the feed and spee
Page 57 and 58: 5714.Tutorial 3Contour millingCNC-C
Page 59 and 60: 59You should now see the part from
Page 61 and 62: 61This dialog contains all the gene
Page 63 and 64: 63Depth cuts are the cuts taken in
Page 65 and 66:
65Now close the parameters dialog w
Page 67 and 68:
15.Tutorial 4Pocket millingCNC-Calc
Page 69 and 70:
69You should now see the part from
Page 71 and 72:
71rapid to cutting speed.Start Dept
Page 73 and 74:
73Depth cuts are the cuts taken in
Page 75 and 76:
75Line Length:Is the length of the
Page 77 and 78:
16.Tutorial 5Backplot in the Editor
Page 79 and 80:
7916.2. The first backplotWhen you
Page 81 and 82:
81After the tools have been configu
Page 83 and 84:
Now everything has been configured,
Page 85 and 86:
85To make a new drawing you must cl
Page 87 and 88:
87For the selection of the location
Page 89 and 90:
8918.Tutorial 7Milling of LettersTh
Page 91 and 92:
91Your screen should now look like
Page 93 and 94:
93Now use window selection to selec
Page 95 and 96:
It is very important to verify/simu
Page 97 and 98:
97To start a new drawing, either cl
Page 99 and 100:
99With parameters, text, and font d
Page 101 and 102:
101Use window selection to select t
Page 103 and 104:
1031.Window select the text.1. Clic
show all

CIMCO

Create successful ePaper yourself

Delete template?

Save as template?