DC3500 AT Commands Manual 500242R01 ... - Cooking Hacks

More documents

Recommendations

Info

DC3500 AT Commands Reference Manual 500242R0112. GPRS commands12.1. Commands Specific to MTs supporting the GPRS12.1.1. Parameter Definition Access Point Name is a string parameter, which is a logical name that is used to select theGGSN or the external packet data network. If the value is null or omitted, then the subscription valuewill be requested. An optional special code placed at the beginning of indicates the kind of theauthentication handling MS/network and may be:- CHAP: challenge handshake authentication protocol- PAP: personal authentication protocol- NONE: authentication protocol not used- code omitted: authentication protocol not usedAn example for the usage of is:+CGDCONT=1,"IP","CHAP:internet.t-d1.de",0,0An optional APN Operator Identifier can also be stated which has to be placed after the mandatoryAPN Network Identifier in the following format:“.mnc.mcc.gprs”.An example for the usage of including an APN Operator Identifier is:+CGDCONT=1,"IP","CHAP:internet.t-d1.de.mnc262.mcc1.gprs",0,0 PDP context identifier meaning a numeric parameter, which specifies a particular PDP contextdefinition. This parameter is valid only locally on the interface TE-MT. is a numeric parameter that controls PDP data compression and can have the values:- 0: off- 1: on (manufacturer preferred compression)- 2: V.42bis data compressionNote: maybe data compressions are not available (this is configured via features in the stack) is a numeric parameter which specifies the delay class acc 3GPP 24.008 (QoS)Important Note: in case delay class = 4 (best effort) is selected, the PS maps this to the best delayclass, in this case delay class 1. is a numeric parameter that controls PDP header compression. The range may be:- 0: off (default value is omitted)- 1: on (manufacturer preferred compression)- 2: RFC1144 (applicable for SNDCP only)- 3: RFC2507 (applicable for SNDCP only)Note: maybe not all header compressions are available (this is configured via features in the stack) is a string parameter that indicates the layer 2 protocol to be used between the TE and MT;only the values “PPP”, “M-OPT-PPP”, “M-HEX” and “M-RAW-IP” are supported. is a numeric parameter which specifies the mean throughput class is a numeric parameter which specifies the peak throughput class is a string parameter that identifies the MT in the address space applicable to the PDP.If the value is null or omitted, then a value may be provided by the TE during the PDP startupprocedure or, failing that, a dynamic address will be requested. Readable with AT-command+CGPADDR.Depending on the IP-version the consists of 4 octetts (IPv4) or 16 octetts (IPv6):IPv4: “ddd.ddd.ddd.ddd”IPv6: “ddd.ddd.ddd.ddd.ddd.ddd.ddd.ddd.ddd.ddd.ddd.ddd.ddd.ddd.ddd.ddd”Confidential DAVISCOMMS (S) PTE LTD 120 /136
DC3500 AT Commands Reference Manual 500242R01 Packet Data Protocol type is a string parameter which specifies the type of packet dataprotocol:- "IP" Internet Protocol (IETF STD 5)- "IPV6" Internet Protocol, version 6 (IETF RFC 2460),... zero to N string parameters whose meanings are specific to the . ForPDP type OSP:IHOSS the following parameters are allowed:- = - = - = is a numeric parameter which specifies the precedence class as:- 0: network subscribed- 1: high priority- 2: normal priority- 3: low priority is a numeric parameter which specifies the reliability class indicates the state of GPRS attachment- 0: detached- 1: attached indicates the state of PDP context activation- 0: deactivated- 1: activatedConfidential DAVISCOMMS (S) PTE LTD 121 /136
Page 7 and 8:
DC3500 AT Commands Reference Manual
Page 9:
Page 12 and 13:
Page 14 and 15:
4.4. Request product serial number
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
4.16. PCCA STD-101 [17] select wire
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
5.12. Service class selection and i
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Defined values parameter sets/shows
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Defined values may be:- 0: query th
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71: 7.27. Price per unit and currency t
Page 72 and 73: DC3500 AT Commands Reference Manual
Page 86 and 87: 8.19. Select cell broadcast message
Page 92 and 93: 9.15. Phase C received EOL alignmen
Page 118 and 119: 11.4. SIM-APPL-TK terminal profile
Page 124 and 125: 12.1.4. Quality of service profile
Page 130 and 131: 12.1.14. Select service for MO SMS
Page 132 and 133: 12.3. Extended Packet Domain AT Com
Page 136: DC3500 AT Commands Reference Manual
show all

DC3500 AT Commands Manual 500242R01 ... - Cooking Hacks

Create successful ePaper yourself

Delete template?

Save as template?