DC3500 AT Commands Manual 500242R01 ... - Cooking Hacks

More documents

Recommendations

Info

12.3. Extended Packet Domain AT CommandsDC3500 AT Commands Reference Manual 500242R0112.3.1. Parameter DefinitionAccess Point Name is a string parameter, which is a logical name thatis used to select the GGSN or the external packet data network. If thevalue is null or omitted, then the subscription value will be requested.An optional special code placed at the beginning of indicatesthe kind of the authentification handling MS/network and may be:- CHAP: challenge handshake authentification protocol- PAP: personal authentification protocol- NONE: authentification protocol not used- code omitted: authentification protocol not usedAn exemple for the usage of is: +CGDCONT=1,"IP","CHAP:internet.t-d1.de",0,0PDP context identifier meaning a numeric parameter, which specifies aparticular PDP context definition. This parameter is valid only locally onthe interface TE-MT.is a numeric parameter that controls PDP data compression and canhave the values:- 0: off- 1: on (manufacturer preferred compression)- 2 : V.42bis data compressionis a numeric parameter which specifies the delay class:erroneous shall be delivered or not. Values:- 0: no- 1: yes- 2: no detect- 3: subscribed value- other values are reserveda numeric parameter that indicates whether the UMTS bearer shallprovide in-sequence SDU delivery or not.- 0: no- 1: yes- 2: subscribed value.- Other values are reserved. consists of dot-separated numeric (0-65535) parameters on the form‘f.t’hexadecimal parameter, value range from 0 to FFFFF. Valid for Ipv6onlyis a numeric parameter that controls PDP header compression(ignored). The range may be:- 0: off (default value is omitted)- 1: on (manufacturer preferred compression); this value leads toimplicitly usage of RFC1144 t.b.d.- 2: RFC1144 (applicable for SNDCP only) a numeric parameter that indicates the guaranteed number of kbits/sdelivered to UMTS (up-link traffic) at a SAP (provided that there is datato deliver). As an example a bitrate of 32kbit/s would be specified as'32' (e.g. AT+CGEQREQ=…,32, …). If the parameter is set to '0' thesubscribed value will be requested. a numeric parameter that indicates the guaranteed number of kbits/sdelivered by UMTS (down-link traffic) at a SAP (provided that there isdata to deliver). As an example a bitrate of 32kbit/s would be specifiedas '32' (e.g. AT+CGEQREQ=…,32, …). If the parameter is set to '0' thesubscribed value will be requested.Confidential DAVISCOMMS (S) PTE LTD 132 /136
DC3500 AT Commands Reference Manual 500242R01is a string parameter that indicates the layer 2 protocol to be usedbetween the TE and MT; only the value “PPP” is supported. a numeric parameter that indicates the maximum number of kbits/sdelivered to UMTS (up-link traffic) at a SAP. a numeric parameter that indicates the maximum number of kbits/sdelivered by UMTS (down-link traffic) at a SAP. As an example abitrate of 32kbit/s would be specified as '32' (e.g.AT+CGEQREQ=…,32, …). If the parameter is set to '0' the subscribedvalue will be requested. a numeric parameter (1,2,3,…) that indicates the maximum allowedSDU size in octets. If the parameter is set to '0' the subscribed valuewill be requestedis a numeric parameter which specifies the mean throughput class numeric parameter, value range from 1 to 8primary PDP Context Identifier is a numeric parameter which specifiesa particular PDP context definition which has been specified by use ofthe +CGDCONT command. The parameter is local to the TE-MTinterface.is a numeric parameter which specifies the peak throughput classis a string parameter that identifies the MT in the address spaceapplicable to the PDP. If the value is null or omitted, then a value maybe provided by the TE during the PDP startup procedure or, failing that,a dynamic address will be requested. Readable with AT-command+CGPADDR.Depending on the IP-version the consists of4 octetts (IPv4) or 16 octetts (IPv6):IPv4: “ddd.ddd.ddd.ddd”IPv6:“ddd.ddd.ddd.ddd.ddd.ddd.ddd.ddd.ddd.ddd.ddd.ddd.ddd.ddd.ddd.ddd”Packet Data Protocol type is a string parameter which specifies thetype of packet data protocol:- X25 (not allowed)- IP Internet Protocol (IETF STD 5)- OSPIH (not allowed)- PPP (not allowed),...zero to N string parameters whose meanings are specific to the. For PDP type OSP:IHOSS the following parameters areallowed:- = - = - = is a numeric parameter which specifies the precedence classis a numeric parameter which specifies the reliability class a string parameter that indicates the target value for the undetected biterror ratio in the delivered SDUs. If no error detection is requested,Residual bit error ratio indicates the bit error ratio in the deliveredSDUs. The value is specified as 'mEe'. As an example a target residualbit error ratio of 5•10-3 would be specified as '5E3' (e.g.AT+CGEQREQ=…,”5E3”,…). '0E0' means subscribed value.a string parameter that indicates the target value for the fraction ofSDUs lost or detected as erroneous. SDU error ratio is defined only forconforming traffic. The value is specified as 'mEe'. As an example atarget SDU error ratio of 5•10-3 would be specified as '5E3' (e.g.AT+CGEQREQ=…,”5E3”,…). '0E0' means subscribed value.consists of dot-separated numeric (0-255) parameters on the form‘a1.a2.a3.a4.m1.m2.m3.m4’, for Ipv4 and‘a1.a2.a3.a4.a5.a6.a7.a8.a9.a10.a11.a12.a13.a14.a15.a16.m1.m2.m3.m4.m5.m6.m7.m8.m9.10.m11.12.13.14.15.16’, for Ipv6 consists of dot-separated numeric (0-65535) parameters on the form‘f.t’Confidential DAVISCOMMS (S) PTE LTD 133 /136
Page 7 and 8:
DC3500 AT Commands Reference Manual
Page 9:
Page 12 and 13:
Page 14 and 15:
4.4. Request product serial number
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
4.16. PCCA STD-101 [17] select wire
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
5.12. Service class selection and i
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Defined values parameter sets/shows
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Defined values may be:- 0: query th
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
7.27. Price per unit and currency t
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83: DC3500 AT Commands Reference Manual
Page 86 and 87: 8.19. Select cell broadcast message
Page 92 and 93: 9.15. Phase C received EOL alignmen
Page 118 and 119: 11.4. SIM-APPL-TK terminal profile
Page 124 and 125: 12.1.4. Quality of service profile
Page 130 and 131: 12.1.14. Select service for MO SMS
Page 136: DC3500 AT Commands Reference Manual
show all

DC3500 AT Commands Manual 500242R01 ... - Cooking Hacks

Create successful ePaper yourself

Delete template?

Save as template?