DC3500 AT Commands Manual 500242R01 ... - Cooking Hacks

More documents

Recommendations

Info

DC3500 AT Commands Reference Manual 500242R017.9. Display control +CDISDescriptionThis set command is used to write the contents of MT text type display elements. An element canconsist of one or several characters. The order of element parameters should follow the rule:first is the element in upper left corner, second is the element to the right and so on.SyntaxCommand syntax: AT+CDISCommandAT+CDIS=[[,[,...]]]Read commandAT+CDIS?Test commandAT+CDIS=?Possible response(s)OKorCME ERROR: +CDIS: [[,...]]OK+CDIS: [,[,...]]OKDefined values is a string type parameter using character set specified by command +CSCS. is a integer type parameter giving the maximum length of corresponding parameter.7.10. Indicator control +CINDDescriptionThis set command is used to set the values of MT indicators. value 0 means that the indicatoris off, 1 means that the indicator is on, 2 is more substantial than 1, and so on. The proprietarycommand +XCIND configure the supported indicators; the default configuration of +XCIND enablesthe support of all indicators listed below. The read command returns the status of MT indicators.The test command returns pairs, where string value is a maximum 16 character descriptionof the indicator and compound value is the allowed value for the indicator. If Bluetooth communicationis supported, the length of the displayed string may be reduced to 127 bytes by using theconfiguration command +XCIND.SyntaxCommand syntax: AT+CINDBecause all possible supported parameters of the set syntax can not be overwritten, the setting willbe ignored and the ATC sends the corresponding final result code OK to TE.CommandPossible response(s)AT+CIND=[[,[,...]]] OKorCME ERROR: Read command+CIND: [,[,...]]AT+CIND?OKTest command+CIND:(“battchg”,(0-5)),(“signal”,(0-5)),(“service”,(0-AT+CIND=?1)),(“sounder”,(0-1)),(“message”,(0-1)),(“call”,(0-1)),(“roam”,(0-1)),(“smsfull”,(0-(2) or proprietary, seenote)),(“gprs”,(0-1)),(“callsetup”,(0-3)),(“callheld”,(0-2))OKDefined values: integer type value, which shall be in range of corresponding values reserved by the norm and their ranges; it may have the values:- “battchg” battery charge level (0-5); see also +CBC for details;- “signal” signal quality (0-5); see also +CSQ for details;- “service” service availability (0-1);Confidential DAVISCOMMS (S) PTE LTD 56 /136
DC3500 AT Commands Reference Manual 500242R01- “sounder” sounder activity (0-1);- “message” message received (0-1);- “call” call in progress (0-1);- 0: means no call active,- 1: means a call is active;- “roam” roaming indicator (0-1); see also +CREG for details;- “smsfull” at receiving of a SMS- 0: or memory locations are available- 1: has become full,- 2*: has become full and a short message has been rejected - see also note below forproprietary enhancements on thisNote: the parameters related to “smsfull” can be enhanced dependent on the defineDR_TE_SM_EXTERNAL:- 3*: a new SMS not-class-2 can not be stored because the external storage is full,whereby the storage on the SIM card is still free.- 4*: a new SMS can not be stored because the external storage and the SMS storageon the SIM card are full.- 5*: the last free SMS entry on the SIM card is used- “gprs” indicating the GPRS registration status:- 0: means not registered and GPRS network not available;- 1: means GPRS available but not registered,- 2: means GPRS registered,- “callsetup” call setup status indicator destinated for Bluetooth usage (not covered byTS27.007); possible values are:- 0: “not currently in call setup”;- 1: “incoming call process ongoing”;- 2: “outgoing call setup is ongoing”;- 3: “remote party being alerted in an ongoing call”;- “callheld” call held indicator destinated for Bluetooth usage (not covered by TS27.007);possible values are:- 0: “no calls held”,- 1: “call is placed on hold or active/held calls swapped (the AG has both an active and aheld call)”,- 2: “call on hold, no active call (i.e. active call released, held call unchanged)”7.11. Mobile termination event reporting +CMERDescriptionThis set command enables or disables sending of unsolicited result codes from TA to TE in the caseof key pressings, display changes and indicator state changes. controls the processing ofunsolicited result codes specified within this command.SyntaxCommand syntax: AT+CMER=[[,[,[,[,]]]]]CommandPossible response(s)Read commandOKAT+CMER?orRead commandAT+CMER?Test commandAT+CMER=?CME ERROR: +CMER:,,,,e.g. +CMER: 1,1,0,2,1OK+CMER: (list of supported ’s),(list of supported’s),(list of supported ’s),(list of supported’s),(list of supported ’s)OK*Not SupportedConfidential DAVISCOMMS (S) PTE LTD 57 /136
Page 7 and 8: DC3500 AT Commands Reference Manual
Page 9: DC3500 AT Commands Reference Manual
Page 14 and 15: 4.4. Request product serial number
Page 20 and 21: 4.16. PCCA STD-101 [17] select wire
Page 26 and 27: 5.12. Service class selection and i
Page 36 and 37: Defined values parameter sets/shows
Page 44 and 45: Defined values may be:- 0: query th
Page 70 and 71: 7.27. Price per unit and currency t
Page 86 and 87: 8.19. Select cell broadcast message
Page 92 and 93: 9.15. Phase C received EOL alignmen
Page 106 and 107:
DC3500 AT Commands Reference Manual
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
11.4. SIM-APPL-TK terminal profile
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
12.1.4. Quality of service profile
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
12.1.14. Select service for MO SMS
Page 132 and 133:
12.3. Extended Packet Domain AT Com
Page 134 and 135:
Page 136:
show all

DC3500 AT Commands Manual 500242R01 ... - Cooking Hacks

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?