DC3500 AT Commands Manual 500242R01 ... - Cooking Hacks

More documents

Recommendations

Info

DC3500 AT Commands Reference Manual 500242R018.8. New message indication +CNMIDescriptionThis set command selects the procedure, how receiving of new SMS from network is indicated to theTE when DTR-signal is ON. IF TE is inactive (DTR-signal OFF), message receiving should be doneas specified in GSM03.38. All SMS classes are supported accordingly.Note (proprietary feature): the SMS’s class 0 which are normally displayed via MMI, can be alsoindicated on DTE via unsolicited result code +CMTI: “SM”,0 , wherein 0 represents a SMS withoutSIM-storage (“SM” indicates only that no other specific setting is needed in order to read the SMS viaAT+CMGR=0).SyntaxCommand syntax: AT+CNMI=[[,[,[,[,]]]]]CommandPossible response(s)AT+CNMI=1,1OKorCMS ERROR: Read command+CNMI=,,,,AT+CNMI?OKTest command+CNMI: (list of supported s),(listAT+CNMI=?of supported s),(list of supporteds),(list of supported s),(list ofsupported s)OKDefined values controls processing of unsolicited result codes specified with this command and may be:- 0: buffer unsolicited result codes in the TA; if the TA buffer is full, the oldest indication maybe discarded and replaced with the new received indications (ring buffer);- 1: discard indication and reject new received message unsolicited result codes when TA-TElink is reserved; otherwise forward them directly to the TE;- 2: buffer unsolicited result codes in the TA when the serial link is busy (e.g. data transfer);otherwise forward them directly to the TE;- 3: Forward unsolicited result codes directly to the TE. TA-TE link specific inband techniqueused to embed result codes and data when TA is in on-line data mode; dies value is notsupported; contains the rules for storing received SMS dependent on its and may be:- 0: No SMS-DELIVER indications are routed to the TE- 1: if SMS-DELIVER is stored in ME/TA, indication of the memory location is routed to the TEusing unsolicited result code: +CMTI: ,- 2: SMS-DELIVER (except class2 SMS) are routed directly to the TE using the unsolicitedresult code: +CMT: [
DC3500 AT Commands Reference Manual 500242R01 may be- 0: No SMS-STATUS-REPORTs are routed to the TE- 1: SMS-STATUS-REPORTs are routed to the TE using unsolicited result code: +CDS:LF> if PDU mode enabled or +CDS:,,[],[],>scts>,, if text mode enabled- 2: if SMS-STATUS-REPORT is stored into ME/TA, indication of the memory location isrouted to the DTE using the unsolicited result code +CDSI: , may be:- 0: TA buffer of unsolicited result codes defined within this command is flushed to the TEwhen 1...3 is entered (OK response shall be given before flushing the codes).- 1: TA buffer of unsolicited result codes defined within this command is cleared when 1...3 is entered.8.9. Read message +CMGRDescriptionThis execution command returns message with location value from message storage to the TE.Note: The parameters ,,,,,, shall be displayed onlywhen setting +CSHD=1 is.Note: The syntax AT+CMGR=0 allows to display a SMS class 0 if it is signalized to ATC, because noMMI is available in the MS (s. also the note from command +CNMI).SyntaxCommand syntax: +CMGR=Command Possible response(s)AT+CMGR=3 for SMS-DELIVER in text mode:+CMGR:,,[],[,,,,,,,]for SMS-SUBMIT in text mode:+CMGR:,,[][,,,,[],,,]for SMS-STATUS-REPORT in text mode:+CMGR:,,,[],[],for SMS-COMMAND in text mode:+CMGR:,,[,,[],[],[],]for CBM storage in text mode:+CMGR:,,,,,in PDU mode:+CMGR: ,[],OKorCMS ERROR: Test command okAT+CMGR=?Defined values: may be in range 0-400; value 0 is possible only if a SMS class 0 is received and previouslythe setting +CNMI=1,… was set.Note: index 1 to n is used for “ME” and n+1 to n+m for “SM”Confidential DAVISCOMMS (S) PTE LTD 79 /136
Page 7 and 8:
DC3500 AT Commands Reference Manual
Page 9:
Page 12 and 13:
Page 14 and 15:
4.4. Request product serial number
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
4.16. PCCA STD-101 [17] select wire
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
5.12. Service class selection and i
Page 28 and 29: DC3500 AT Commands Reference Manual
Page 36 and 37: Defined values parameter sets/shows
Page 44 and 45: Defined values may be:- 0: query th
Page 70 and 71: 7.27. Price per unit and currency t
Page 86 and 87: 8.19. Select cell broadcast message
Page 92 and 93: 9.15. Phase C received EOL alignmen
Page 118 and 119: 11.4. SIM-APPL-TK terminal profile
Page 124 and 125: 12.1.4. Quality of service profile
Page 128 and 129:
Page 130 and 131:
12.1.14. Select service for MO SMS
Page 132 and 133:
12.3. Extended Packet Domain AT Com
Page 134 and 135:
Page 136:
show all

DC3500 AT Commands Manual 500242R01 ... - Cooking Hacks

Create successful ePaper yourself

Delete template?

Save as template?