DC3500 AT Commands Manual 500242R01 ... - Cooking Hacks

More documents

Recommendations

Info

9.15. Phase C received EOL alignment +FEADC3500 AT Commands Reference Manual 500242R01DescriptionThis command enables optional octet-alignment of EOL markers in received T.4 data stream. It doesnot apply to T.6 data, or to any form of data.SyntaxCommand syntax: AT+FEA=Defined values may be:- 0: determines that T.4 EOL patterns are bit aligned (as received)- 1: determines that the last received bits of T.4 EOL patterns are octet aligned by the DCE,with necessary zero fill bits inserted.9.16. Format conversion +FFCDescriptionThis command determines the DCE response to mismatches between the phase C data deliveredafter the +FDT command and the data format parameters negotiated for the facsimile session.SyntaxCommand syntax: AT+FFC=,,,Defined values vertical resolution format codes may be:- 0: ignored- 1: enabled- 2: enabled for 1-D data- 3: enabled for 2-D data data format codes may be:- 0: ignored- 1: checking enabled- 2: conversion page length format codes may be:- 0: ignored- 1: checking enabled- 2: conversion for 1-D data- 3: conversion enabled for 2-D data page with format codes may be:- 0: ignored- 1: checking enabled- 2: conversion enabledConfidential DAVISCOMMS (S) PTE LTD 92 /136
DC3500 AT Commands Reference Manual 500242R019.17. Call termination status +FHSDescriptionThis command indicates the cause of a hang-up +FHS is set by the DS at the conclusion of a FAXsession. The DCE resets this value to 0 at the beginning of phase A.SyntaxCommand syntax: AT+FHS? (read syntax only)Response syntax: Defined values may be in range 0-FFH9.18. Procedure interrupt enable +FIEDescriptionThis command allows either station to initiate interrupts; the other station may ignore or accept therequests.SyntaxCommand syntax: AT+FIE=Defined values only value 0 is allowed; it means that the procedure interrupt requests from the remotestation are ignored and not reported to DTE.9.19. Current session parameters +FISDescriptionThis command allows the DTE to sense and constrain the capabilities used for the current session.SyntaxCommand syntax: AT+FIS=,,,,,,,,Defined valuesSee +FCC.9.20. Inactivity timeout +FITDescriptionThis command allows to provide an inactivity timer which allows the DS to break away from anunsuccessful connection attempt at any stage of a facsimile transfer.SyntaxCommand syntax: AT+FIT=[[,]]Defined values valid time in range 0-255 only value 0 possible and means: upon timeout the DCE shall go on-hook, executing animplied ATH command, then reset to +FCLASS=0.Confidential DAVISCOMMS (S) PTE LTD 93 /136
Page 7 and 8:
DC3500 AT Commands Reference Manual
Page 9:
Page 12 and 13:
Page 14 and 15:
4.4. Request product serial number
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
4.16. PCCA STD-101 [17] select wire
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
5.12. Service class selection and i
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Defined values parameter sets/shows
Page 38 and 39:
Page 40 and 41:
Page 42 and 43: DC3500 AT Commands Reference Manual
Page 44 and 45: Defined values may be:- 0: query th
Page 70 and 71: 7.27. Price per unit and currency t
Page 86 and 87: 8.19. Select cell broadcast message
Page 118 and 119: 11.4. SIM-APPL-TK terminal profile
Page 124 and 125: 12.1.4. Quality of service profile
Page 130 and 131: 12.1.14. Select service for MO SMS
Page 132 and 133: 12.3. Extended Packet Domain AT Com
Page 136: DC3500 AT Commands Reference Manual
show all

DC3500 AT Commands Manual 500242R01 ... - Cooking Hacks

Create successful ePaper yourself

Delete template?

Save as template?