Busch-Watchdog presence detector Type: 6131-74-101

More documents

Recommendations

Info

ABB i-bus ® EIBBusch-Watchdog presence detectorType: 6131-74-101Channel adjustmentsThe setting of the threshold for the lightsensor as well as the recovery timecan be carried out using thepotentiometer at the back of thepresence detector. There is a separatesetting aid for this purpose. Theillumination threshold is defined forchannel 1 with the “Lux1potentiometer”. The “HVACpotentiometer” presets the illuminationthreshold for channel 2. The“Illumination potentiometer” sets therecovery time for both channels.Alternatively, the settings can becarried out in ETS. To do so, theadjustment parameters should bechanged from “... potentiometer” to“ETS”.With the parameter “Thresholdillumination adjustable with”, thebrightness value that triggers thepresence detector can be indicated.Values between 5 lux and 1000 luxcan be entered. The recovery time canbe set with the two parameters “Timebase of recovery time” and “Time factorof recovery time”. The recovery time isproduced from the base and the factor:Recovery time = Base * Factor.Brightness-dependent switchingA further communication object canalso be enabled separately for eachchannel with the parameter “Activationobject brightness dependentswitching”. If the communication object“Brightness dependent switchingchannel ...” receives a “1”, thepresence detector switches on withoutdependence on brightness. Thethreshold settings that have beencarried out with the potentiometer atthe rear of the device or with ETS, donot have any significance for theduration of the activation. If a “0” isreceived at the object, the presencedetector only sends “On” telegramsagain once the brightness value hasfallen below the illumination threshold.Light sourceWith an increasing proportion ofexternal light, the presence detectorsends an “Off” telegram as soon as theexternal light has reached the requiredilluminance. The type of light sourcemust be indicated for this purpose.Example:Illuminance 500 luxThe illumination threshold of 500 lux ispreset via the potentiometer on thepresence detector or via the ETSprogram.If movement is now detected in a darkroom in the morning and thebrightness value lies below 500 lux,the presence detector sends an “On”telegram when it records movement.a) switched light source:When the luminaires are switched on,they generate a luminance of 500 lux.The external light coming in is addedto this. The presence detector switchesoff if it measures a luminance level of1000 lux.b) controlled light source (constantbrightness):If a conventional constant brightnesscontroller is built into the luminaires,this regulates the proportion of artificiallight so that the measured luminancestays constant at 500 lux. If thepresence detector now records ameasurement of more than 500 lux,the luminaires have already beendimmed down to the minimumbrightness value and are switched off.May 2002 2 - 77
ABB i-bus ® EIBBusch-Watchdog presence detectorType: 6131-74-101HVACThe presence detector can activate aheating or ventilation controller with itsobject “Movement HVAC”. The objectsends telegrams without dependenceon the brightness value.The ON delay is the period which theHVAC channel needs until it detects amovement. This period is automaticallyset by default by the presence detector.It can however also be preselected. Todo so, the parameter “Switch ON isadjustable” must be set to “by ETS”.The time is composed of a base and afactor in the same way as the recoverytime.If the switch ON behaviour is set withthe HVAC potentiometer, the followingshould be noted:– If an OFF delay between 1 and 10min is assigned with thepotentiometer, the ON delay is set at30 s. This setting can for exampleswitch on an extractor fan in the WC.– If the OFF delay is set at longer than10 min, the ON time is based on thefrequency of detection of movement.In a standard office, the heatingsystem is only switched on when theemployee stays there for a longerperiod. In a conference room whichis seldom used, the heating is notactivated when someone enters theroom briefly and then leaves againafter a short period.The object “Movement HVAC” cantrigger a telegram after detection of amovement and after an adjustablerecovery time. With the parameter“Type of movement object”, it ispossible to set whether 1 bit switchingtelegrams or 1 byte value telegramsare triggered. The switching telegramscan also be sent cyclically in the sameway as the movement channels.Bus voltage recoveryThe states of the communicationobjects “Movement channel ... / Telegr.switch” adopt a defined status on busvoltage recovery. The states ofchannels 1 and 2 can be definedseparately. There are thus nounnecessary switching operations onbus voltage recovery.Defined states can also be selected forthe objects “Brightness dependentswitching channel ...”. The parametersare only visible if the objects havepreviously been enabled.2 - 78 May 2002
Page 1 and 2: ABB i-bus ® EIBBusch-Watchdog pres
Page 9: ABB i-bus ® EIBBusch-Watchdog pres

Busch-Watchdog presence detector Type: 6131-74-101

Create successful ePaper yourself

Delete template?

Save as template?