Summagraphics D1000 User's Manual - Summa Online

More documents

Recommendations

Info

It is not necessary to unroll the media manually from the roll. The cutter willunroll the media automatically at reduced speed during the load sequence.9. The positioning and routing of sheet material is identical to that of rollmedia.10. The cutter is now ready for the actual load procedure, which may becontrolled from the control panel.However, most jobs can be done without the extended load proceduredescribed in section 1.10.1.10. MEDIA LOAD PROCEDURESAFE OPERATIONTrademark Acknowledgements
Do not place any objects in front of, or behind the cutter that could interferewith cutter operation. Make sure the media is free to move back and forth.Keep hands, hair, clothing and jewelry away from moving parts.Turn the power on and the following message will appear on the LCD screen :PLEASE WAITLOADING...KThe cutter will automatically start executing a minimal loading procedure consisting of : - a media widthmeasurement- a 45° test- media is unwound over a length equal to the width measuredbetween the edge pinch rollersWhen the next display appears, the cutter is ready to receive a file :500mm/s 120 gK.45mm ONLINE 1When sending a cut file , the cutter will automatically pull the required media from the roll. The pulling isdone in steps such that for each step the length pulled off the roll is identical to the width measuredbetween the pinch rollers.IMPORTANTTracking of longer signs is only guaranteed when you perform thefull load procedure !Proceed as follows to complete the full load procedure :Press the RESET/LOAD key and the following message will appear on the LCD screen :SET ORIGINKX=0 Y=YYYY Press the RESET/LOAD key again and the following message will appear on the LCD screen :LOAD1= ROLL 2= SHEETKNotice
Page 1 and 2: SUMMAGRAPHICS D1000USER’S MANUALI
Page 6 and 7: 2.5. INTERNAL TEST MENU............
Page 8 and 9: SECTION 1GENERAL INFORMATION1.1. IN
Page 10 and 11: Depth, stand included 870 mm 34.30
Page 12 and 13: Serial : I/O Port connector DB-9PMa
Page 14 and 15: 1.3. CUTTER ACCESSORIES AND CONSUMA
Page 16 and 17: In order to get acquainted with you
Page 18 and 19: 6. Power ON/OFF switch.- This rocke
Page 20 and 21: EARTH CONNECTION!IMPORTANT OPERATIO
Page 22 and 23: FIGURE 1-6BLADE LENGTH ADJUSTMENT4.
Page 24 and 25: After setting the cutting depth and
Page 26 and 27: Depending on the width of the media
Page 30 and 31: Press the 1 key if you want to load
Page 32 and 33: SECTION 2OPERATION2.1. THE CONTROL
Page 34 and 35: • Press the LEFT or RIGHT jogging
Page 36 and 37: 2.1.8. THE TOOL UP/DOWN KEYThe TOOL
Page 38 and 39: Four different user configurations
Page 40 and 41: FIGURE 2-3 :FLOWCHART SHOWING FACTO
Page 42 and 43: On the LCD, the active pen pressure
Page 44 and 45: The parity setting of your cutter M
Page 46 and 47: 2.5.1. CUT BORDERFIGURE 2-4 :INTERN
Page 48 and 49: CAUTIONThe following test routines
Page 50 and 51: SECTION 3GENERAL INFORMATION3.1. MA
Page 52 and 53: Trademark AcknowledgementsFIGURE 3-
Page 54 and 55: 6. The computer end of the cable mu
Page 56 and 57: APPENDIX AMEDIA CERTIFICATIONTypes

Summagraphics D1000 User's Manual - Summa Online

Create successful ePaper yourself

Delete template?

Save as template?