Summagraphics D1000 User's Manual - Summa Online

More documents

Recommendations

Info

SECTION 2OPERATION2.1. THE CONTROL PANELFigure 2-1 shows the control panel of the Summagraphics D1000 cutter. The main functions of the liquidcrystal display (LCD) and the control panel keys are explained in the following paragraphs.FIGURE 2-1:SUMMAGRAPHICS D1000 CUTTER, CONTROL PANEL2.1.1. THE LIQUID CRYSTAL DISPLAYTrademark Acknowledgements
The 32-character liquid crystal display (LCD) contains two lines of 16 characters each. The LCDprovides cutter status information during operations and displays menu options for the configuration ofthe cutter.The contrast of the LCD can be adjusted from the control panel in order to ensure optimum readabilityunder varying lighting conditions.Instructions for adjusting the LCD contrast are given in Section 2.6.12.The various menu and submenu items are always presented in a loop, which means that, when the lastmenu or submenu item is displayed, pressing the appropriate key will automatically take you back to thefirst item of the same menu or submenu.Next to the status messages and/or menu options displayed on the LCD, arrow symbols representing theUP, DOWN, LEFT and RIGHT jogging keys or ENTER key will tell you what keys to press to go tothe next menu item (top line of the display) or to the next value for a given submenu item (bottom line ofthe display).2.1.2. THE RESET/LOAD KEYThe RESET/LOAD key is used to move the origin, to initiate a load sequence, to reset the cutter, toabort the cut in progress or to recut the last file. When the RESET/LOAD key is pressed, the cutter goesoffline, suspends all operations in progress and displays the RESET/LOAD menu. Press theRESET/LOAD key until SET ORIGIN, LOAD, RESET, ABORT or RECUT is displayed. To confirmRESET, ABORT or RECUT press the ENTER key. To execute the SET ORIGIN instruction move theknife origin using the UP, DOWN, LEFT and RIGHT jogging keys and press the ENTER key toconfirm the new origin position. To initiate the LOAD instruction press the 1 or 2 key to initiate a loadsequence for a ROLL or SHEET respectively. Upon termination of any of these instructions, the cuttergoes online again.The SET ORIGIN instruction is used to move the knife origin.The LOAD instruction is used to initiate a load sequence.The RESET instruction performs a complete reset of the cutter.The ABORT instruction simply cancels the cut in progress. Aborting a cut will not reset the cutterparameters: the parameters which had been selected for the cut remain in effect.The RECUT instruction recuts the last file sent to the cutter (provided that it fitted into the buffer).2.1.3. THE ONLINE KEYThe ONLINE key toggles between online and offline operation. When the ONLINE key is pressed, theselected mode (ONLINE or OFFLINE) is displayed on the LCD.Selecting OFFLINE will suspend all operations in progress. Pressing the ONLINE key while the cutter isoffline will make the cutter go online again, resuming the suspended operation.While the cutter is offline, the following operations can be performed:Notice
Page 1 and 2: SUMMAGRAPHICS D1000USER’S MANUALI
Page 6 and 7: 2.5. INTERNAL TEST MENU............
Page 8 and 9: SECTION 1GENERAL INFORMATION1.1. IN
Page 10 and 11: Depth, stand included 870 mm 34.30
Page 12 and 13: Serial : I/O Port connector DB-9PMa
Page 14 and 15: 1.3. CUTTER ACCESSORIES AND CONSUMA
Page 16 and 17: In order to get acquainted with you
Page 18 and 19: 6. Power ON/OFF switch.- This rocke
Page 20 and 21: EARTH CONNECTION!IMPORTANT OPERATIO
Page 22 and 23: FIGURE 1-6BLADE LENGTH ADJUSTMENT4.
Page 24 and 25: After setting the cutting depth and
Page 26 and 27: Depending on the width of the media
Page 28 and 29: It is not necessary to unroll the m
Page 30 and 31: Press the 1 key if you want to load
Page 34 and 35: • Press the LEFT or RIGHT jogging
Page 36 and 37: 2.1.8. THE TOOL UP/DOWN KEYThe TOOL
Page 38 and 39: Four different user configurations
Page 40 and 41: FIGURE 2-3 :FLOWCHART SHOWING FACTO
Page 42 and 43: On the LCD, the active pen pressure
Page 44 and 45: The parity setting of your cutter M
Page 46 and 47: 2.5.1. CUT BORDERFIGURE 2-4 :INTERN
Page 48 and 49: CAUTIONThe following test routines
Page 50 and 51: SECTION 3GENERAL INFORMATION3.1. MA
Page 52 and 53: Trademark AcknowledgementsFIGURE 3-
Page 54 and 55: 6. The computer end of the cable mu
Page 56 and 57: APPENDIX AMEDIA CERTIFICATIONTypes

Summagraphics D1000 User's Manual - Summa Online

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?