EZ-Guide Plus Lightbar Guidance System Getting Started Guide

More documents

Recommendations

Info

To simultaneously receive and output NMEA messages, attach the lightbar andexternal receiver to a computer or device and then configure the lightbar and externalreceiver. For more information, refer to the EZ-Guide Plus Lightbar: UsingSimultaneous NMEA Input and NMEA Output Support Note on www.EZ-Guide.com.High accuracy smart antennaThe following figure shows how to connect the high accuracy smart antenna to thelightbar.LightbarP/N 52026-00P/N 52033High accuracy smart antennaP/N 50166Optional remote controlNote — If using a high accuracy smart antenna with a lightbar which does not havean integrated GPS receiver, you do not need to change any settings on the EZ-GuidePlus lightbar guidance system. If you are using a lightbar with internal GPS, set theData Port to TSIP Receiver.Configuring the receiverWhen the high accuracy smart antenna is connected to the EZ-Guide Plus lightbarand the Input field on the Data Port Settings screen is set to TSIP Receiver, thereceiver is automatically configured.50 Using GPS EZ-Guide Plus Lightbar Guidance System Getting Started Guide
DGPS box receiverThe following figure shows how to connect the DGPS box receiver to the lightbar.LightbarP/N 52026-00P/N 52033DGPS box receiverP/N 30945-00Optional remote controlTo switch inputand pulse outputIf you are using a DGPS box receiver, you need to disable the 1HZ VTG setting:1. From the Home screen, press 3 until Configuration appears and then press2.2. Press 3 until the GPS Config screen appears.3. Press 2 until the 1Hz NMEA screen appears.4. Change VTG to vtg as follows:a. Press 3 to highlight VTG.b. Press 2 to change VTG to vtg.c. Press 4 to save the setting.Selecting the correct OmniSTAR satellite manually1. From the Home screen, press 3 until the Configuration screen appears.2. Press 2 and then press 3 until the DGPS Config screen appears.3. Press 2 until the DGPS Source screen appears.4. Press 3 and then 2 to change the setting to OmniSTAR.5. Press 2 until the EZ Sat: Omni* screen appears.6. Press 3 and then 2 to select the correct region.EZ-Guide Plus Lightbar Guidance System Getting Started Guide Using GPS 51
Page 3 and 4: GETTING STARTED GUIDEEZ-Guide® Plu
Page 5 and 6: IMPLIED WARRANTIES OF MERCHANTABILI
Page 7 and 8: 3GENERAL.3.1This Agreement shall be
Page 9 and 10: ContentsIntroduction 9What’s in t
Page 11 and 12: www.trimble.comStandard systemCONNE
Page 13 and 14: CFor more information and ordering
Page 15 and 16: Getting StartedThis section describ
Page 17 and 18: ViewsTo change between the four vie
Page 19 and 20: Pass code restrictionThe EZ-Guide P
Page 21 and 22: Path Display on the Summary screenT
Page 23 and 24: Status text itemCurrent RateCurrent
Page 25 and 26: Getting GuidanceThe EZ-Guide Plus l
Page 27 and 28: Swaths drawn on screen extend 1 km
Page 29 and 30: Simple curves (using Adaptive curve
Page 31 and 32: B4. On your final headland, press D
Page 34 and 35: Loading an existing AB Line1. Selec
Page 36 and 37: Each nudge moves the guidance line
Page 38 and 39: Connecting a deviceTo connect the l
Page 40 and 41: 38 Getting Guidance EZ-Guide Plus L
Page 42 and 43: Warning optionsConfigure the follow
Page 44 and 45: About the GPS receiversSome common
Page 46 and 47: Configuring the receiverThis sectio
Page 48 and 49: You can select from four levels of
Page 50 and 51: There are two status text options f
Page 54 and 55: DGPS smart antenna and DGPS/OmniSTA
Page 56 and 57: Menu Menu option Description Defaul
Page 58 and 59: Menu Menu option Description Defaul
Page 60 and 61: 58 Overview of the Menu EZ-Guide Pl
Page 62 and 63: Problem Possible cause SolutionFEW
Page 64 and 65: 62 Troubleshooting EZ-Guide Plus Li
Page 66: esetting nudge 34resume 34rowfinder

EZ-Guide Plus Lightbar Guidance System Getting Started Guide

Create successful ePaper yourself

Delete template?

Save as template?