EZ-Guide Plus Lightbar Guidance System Getting Started Guide

More documents

Recommendations

Info

58 Overview of the Menu EZ-Guide Plus Lightbar Guidance System Getting Started Guide
TroubleshootingProblem Possible cause SolutionScreen is blank orhard to seeI need to reset thestart of the firstswathMy lightbar LEDs,buttons, or screendo not appear to beworking properlyNO GPS COMMSNO GPS POSITIONSmessage flashes onscreenBacklight is offBacklight level needs tobe adjustedThe lightbar has lockedupContrast is wrongNo powerYou have mapped thestart of the first swath atthe wrong timeThere is a fault with thehardwareThe lightbar is notcommunicating with theintegrated GPS receiverThe external GPS receiveris not connected to thelightbarThe antenna is notconnected to the lightbarThe antenna, antennacable, or GPS antennaconnection is faultyTurn on the cab light. Then use Brightness/Contrast to turnon the backlight.Select Brightness/Contrast screen to change thebrightness.Disconnect power, wait 30 seconds, and then reapplypower.Press and hold o as you reapply power. Contrast is resetto the default value.Make sure that the lightbar is connected to a power source.Press u to select the A icon and then press o to resetPoint A.Run hardware tests. From the Lightbar menu, select Tests.Run any or all of the tests. If any of the tests fail, contactyour local reseller for information on repairing or replacingthe lightbar.The GPS receiver or lightbar is faulty. Contact your localreseller for information about repairing or replacing thefaulty item.Connect the external GPS receiver to the data port on thelightbar. In the Data Port Settings screen, set Input toExternal GPS or TSIP Receiver.To use the integrated GPS receiver, set the Data Port Inputfield to None.Connect the antenna to the lightbar or to the external GPSreceiver. See Installing the system, page 11.From the Configuration menu, select GPS / GPSDiagnostics. Press u. If the Antenna option displays None,there is a problem with the antenna, antenna cable, or theGPS antenna connection.Contact your local reseller for information about repairing orreplacing the faulty item.EZ-Guide Plus Lightbar Guidance System Getting Started Guide Troubleshooting 59
Page 3 and 4:
GETTING STARTED GUIDEEZ-Guide® Plu
Page 5 and 6:
IMPLIED WARRANTIES OF MERCHANTABILI
Page 7 and 8:
3GENERAL.3.1This Agreement shall be
Page 9 and 10: ContentsIntroduction 9What’s in t
Page 11 and 12: www.trimble.comStandard systemCONNE
Page 13 and 14: CFor more information and ordering
Page 15 and 16: Getting StartedThis section describ
Page 17 and 18: ViewsTo change between the four vie
Page 19 and 20: Pass code restrictionThe EZ-Guide P
Page 21 and 22: Path Display on the Summary screenT
Page 23 and 24: Status text itemCurrent RateCurrent
Page 25 and 26: Getting GuidanceThe EZ-Guide Plus l
Page 27 and 28: Swaths drawn on screen extend 1 km
Page 29 and 30: Simple curves (using Adaptive curve
Page 31 and 32: B4. On your final headland, press D
Page 34 and 35: Loading an existing AB Line1. Selec
Page 36 and 37: Each nudge moves the guidance line
Page 38 and 39: Connecting a deviceTo connect the l
Page 40 and 41: 38 Getting Guidance EZ-Guide Plus L
Page 42 and 43: Warning optionsConfigure the follow
Page 44 and 45: About the GPS receiversSome common
Page 46 and 47: Configuring the receiverThis sectio
Page 48 and 49: You can select from four levels of
Page 50 and 51: There are two status text options f
Page 52 and 53: To simultaneously receive and outpu
Page 54 and 55: DGPS smart antenna and DGPS/OmniSTA
Page 56 and 57: Menu Menu option Description Defaul
Page 58 and 59: Menu Menu option Description Defaul
Page 62 and 63: Problem Possible cause SolutionFEW
Page 64 and 65: 62 Troubleshooting EZ-Guide Plus Li
Page 66: esetting nudge 34resume 34rowfinder
show all

EZ-Guide Plus Lightbar Guidance System Getting Started Guide

Create successful ePaper yourself

Delete template?

Save as template?