SINAMICS S120 Functi.. - Gregbotos.com

More documents

Recommendations

Info

Extended FunctionsAutomatic restart (vector, infeed)Starting attempts (p1211) and waiting time (p1212)p1211 is used to specify the number of starting attempts. The number is internallydecremented after each successful fault acknowledgement (line supply voltagemust be re-applied or the infeed signals that it is ready. Fault F07320 is output ifthe number of parameterized start attempts has been reached.When 1211 = x, x + 1 starting attempts are made.NoteA start attempt immediately starts when the fault occurs.The faults are automatically acknowledged in intervals of half the waiting timep1212.After successfully acknowledgment and the voltage returns, then the system isautomatically powered-up again.The start attempt has been successfully completed if the flying restart and the motormagnetization (induction motor) has been completed (r0056.4 = 1) and one additionalsecond has expired. The starting counter is only reset back to the initialvalue p1211 after this time.If additional faults occur between successful acknowledgement and the end of thestarting attempt, then the starting counter, when it is acknowledged, is also decremented.Monitoring time line supply return (p1213)The monitoring time starts when the faults are detected. If the automatic acknowledgementsare not successful, the monitoring time runs again. If the drive has notsuccessfully started again after the monitoring time has expired (flying restart andmotor magnetization must have been completed: r0056.4 = 1), fault F07320 is output.The monitoring is de-activated with p1213 = 0. If p1213 is set lower than thesum of p1212, the magnetization time r0346 and the additional delay time due toflying restart, then fault F07320 is generated at each restart. If, for p1210 = 1, thetime in p1213 is set lower than p1212, then fault F07320 is also generated at everyrestart attempt. The monitoring time must be extended if the faults that occur cannotbe immediately and successfully acknowledged (e.g. when faults are permanentlypresent).4-198© Siemens AG 2006 All Rights ReservedSINAMICS S120 Function Manual, 03/2006 Edition
Extended FunctionsAutomatic restart (vector, infeed)Commissioning1. Activating the function for vector and infeed drive object– Automatic restart: set mode (p1210).– Flying restart: Activate function (p1200).2. Set starting attempts (p1211).3. Set waiting times (p1212, p1213).4. Check function.Important parameters (refer to the List Manual) r0863 CO/BO: Drive coupling status word/control word p1207 BI: Automatic restart – connection to the following DO p1208 BI: Automatic restart – infeed fault p1210 Automatic restart, mode p1211 Automatic restart, attempts to start p1212 Automatic restart, delay time start attempts p1213 Automatic restart, waiting time increment© Siemens AG 2006 All Rights ReservedSINAMICS S120 Function Manual, 03/2006 Edition4-199
Page 1:
Function Manual 03/2006 Editionsina
Page 4 and 5:
Safety information/instructionsThis
Page 6 and 7:
ForewordTable F-1Useful phases and
Page 8 and 9:
ForewordTechnical supportIf you hav
Page 10 and 11:
ForewordESD information!CautionAn e
Page 12 and 13:
Foreword!Caution The surface temper
Page 14 and 15:
Table of Contents3.1.10 Sensorless
Page 16 and 17:
Table of Contents4.24.3 Referencing
Page 18 and 19:
InfeedActive Infeed1.1 Active Infee
Page 20 and 21:
InfeedActive InfeedOperating modes
Page 22 and 23:
InfeedActive InfeedIdentification m
Page 24 and 25:
InfeedActive InfeedSwitching off th
Page 26 and 27:
InfeedActive InfeedExample: setting
Page 28 and 29:
InfeedSmart InfeedConnection diagra
Page 30 and 31:
InfeedSmart Infeed1.2.2 Line and DC
Page 32 and 33:
InfeedSmart InfeedSwitching on the
Page 34 and 35:
InfeedBasic Infeed1.3 Basic Infeed1
Page 36 and 37:
InfeedBasic InfeedSwitching on the
Page 38 and 39:
InfeedLine contactor control1.4 Lin
Page 40 and 41:
InfeedPre-charging and bypass conta
Page 42 and 43:
Extended Setpoint ChannelExtended s
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Operating ModesServo control3.1 Ser
Page 68 and 69:
Operating ModesServo controlFunctio
Page 70 and 71:
Operating ModesServo controlParamet
Page 72 and 73:
Operating ModesServo controlOFF res
Page 74 and 75:
Operating ModesServo control3.1.5 T
Page 76 and 77:
Operating ModesServo controlFixed a
Page 78 and 79:
Operating ModesServo controlActivat
Page 80 and 81:
Operating ModesServo control3.1.6
Page 82 and 83:
Operating ModesServo controlOvervie
Page 84 and 85:
Operating ModesServo controlCurrent
Page 86 and 87:
Operating ModesServo controlLow-pas
Page 88 and 89:
Operating ModesServo controlBand-st
Page 90 and 91:
Page 92 and 93:
Operating ModesServo controlStructu
Page 94 and 95:
Page 96 and 97:
Operating ModesServo controlSwitcho
Page 98 and 99:
Page 100 and 101:
Operating ModesServo controlMotor d
Page 102 and 103:
Operating ModesServo controlInducti
Page 104 and 105:
Operating ModesServo controlSynchro
Page 106 and 107:
Operating ModesServo controlMotor M
Page 108 and 109:
Operating ModesServo controlExample
Page 110 and 111:
Operating ModesServo control!Warnin
Page 112 and 113:
Operating ModesServo controlTable 3
Page 114 and 115:
Operating ModesServo controlDescrip
Page 116 and 117:
Operating ModesServo controlFunctio
Page 118 and 119:
Operating ModesServo controlSignal
Page 120 and 121:
Page 122 and 123:
Operating ModesVector control3.2 Ve
Page 124 and 125:
Operating ModesVector controlfStart
Page 126 and 127:
Operating ModesVector control3.2.3
Page 128 and 129:
Operating ModesVector controlParame
Page 130 and 131:
Operating ModesVector controlExampl
Page 132 and 133:
Page 134 and 135:
Operating ModesVector controlNoteTh
Page 136 and 137:
Page 138 and 139:
Operating ModesVector controlKpTnSp
Page 140 and 141:
Page 142 and 143:
Operating ModesVector controlThese
Page 144 and 145:
Operating ModesVector controlDescri
Page 146 and 147:
Page 148 and 149: Operating ModesVector control3.2.11
Page 150 and 151: Operating ModesVector controlIn add
Page 152 and 153: Operating ModesVector controlCarryi
Page 154 and 155: Operating ModesVector control3.2.12
Page 156 and 157: Operating ModesVector controlIntegr
Page 158 and 159: Operating ModesVector V/f control (
Page 162 and 163: ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ
Page 170 and 171: Operating ModesInformation on commi
Page 178 and 179: Extended Functions“Technology con
Page 184 and 185: ÑÑÑÑÑÑÑÑÑÑÑÑExtended Fu
Page 186 and 187: Extended FunctionsSimple brake cont
Page 188 and 189: Extended FunctionsSimple brake cont
Page 190 and 191: Extended Functions“Extended brake
Page 196 and 197: Extended FunctionsAutomatic restart
Page 200 and 201: Extended FunctionsFunction module,
Page 202 and 203: Extended FunctionsFunction module,
Page 204 and 205: Extended FunctionsRedundant operati
Page 206 and 207: Extended FunctionsTechnology functi
Page 208 and 209: Extended FunctionsMotor changeoverO
Page 210 and 211: Extended FunctionsMotor changeoverT
Page 212 and 213: Extended FunctionsMotor changeoverT
Page 214 and 215: Extended FunctionsSimulation mode (
Page 216 and 217: Extended FunctionsParking axis and
Page 218 and 219: Extended FunctionsBoot with partial
Page 220 and 221: Extended FunctionsBoot with partial
Page 222 and 223: Extended Functionsdv/dt filter plus
Page 224 and 225: Extended FunctionsFlying restart (v
Page 226 and 227: Extended FunctionsArmature short-ci
Page 228 and 229: Extended FunctionsArmature short-ci
Page 230 and 231: Extended FunctionsSwitching-in a dr
Page 232 and 233: Extended Functions“Braking Module
Page 234 and 235: Extended FunctionsFunction module
Page 236 and 237: Extended FunctionsFunction module p
Page 248 and 249:
Extended FunctionsFunction module
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Extended FunctionsBypass (vector)Co
Page 280 and 281:
Extended FunctionsBypass (vector)Tr
Page 282 and 283:
Extended FunctionsBypass (vector)4.
Page 284 and 285:
Extended FunctionsBypass (vector)4.
Page 286 and 287:
Extended FunctionsBypass (vector)Ta
Page 288 and 289:
Extended FunctionsBypass (vector)Ov
Page 290 and 291:
Extended FunctionsSynchronization (
Page 292 and 293:
Extended FunctionsTerminal Module 4
Page 294 and 295:
Extended FunctionsTerminal Module 4
Page 296 and 297:
Extended FunctionsChanging over uni
Page 298 and 299:
Extended FunctionsApplication examp
Page 300 and 301:
Extended FunctionsApplication examp
Page 302 and 303:
Extended FunctionsPosition tracking
Page 304 and 305:
Extended FunctionsPosition tracking
Page 306 and 307:
Basic Information about the Drive S
Page 308 and 309:
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
Page 316 and 317:
Page 318 and 319:
Page 320 and 321:
Page 322 and 323:
Page 324 and 325:
Page 326 and 327:
Page 328 and 329:
Availability of SW FunctionsTable A
Page 330 and 331:
Availability of SW FunctionsTable A
Page 332 and 333:
List of AbbreviationsAbbreviation G
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
List of AbbreviationsNotesB-338© S
Page 340 and 341:
ReferencesInteractive catalogs/CA01
Page 342 and 343:
References/PFT6S/SINAMICS Synchrono
Page 344 and 345:
ReferencesNotesC-344© Siemens AG 2
Page 346 and 347:
IndexExtended torque control, 3-80F
Page 348 and 349:
IndexTorque control, 3-137Extended,
Page 351 and 352:
Overview of SINAMICS Documentation
show all

SINAMICS S120 Functi.. - Gregbotos.com

Create successful ePaper yourself

Delete template?

Save as template?