LS7 Corvette Mechanical Repair Specs (PDF) - Bakes Online

More documents

Recommendations

Info

Print Preview Version 8.0 PubTeX output 2006.06.15:1036 File: C:\DOCUME~1\PCOMPO~1.IGS\LOCALS~1\Temp\.aptcache\2006LS7/tfa01804.dvi User: PComposer Page: 1262006 Y Car GMX245 Corvette7.0L (LS7) Engine Mechanical15525568. Drive the bearing from the block bore.Important: In order to remove the front camshaft bearing, operate the tool from the rear of the block, usingthe guide cone in the rear camshaft bearing bore.9. Repeat the above procedures in order to remove the remaining bearings.Tool Usage InformationBearing, Expander, and Expander Driver Information66100• The tool consists of a guide cone (1), driving washers (2 or 3), expander bearing drivers (4–8), driver bars (9 or 10),expander jaws (11), expander sleeve (12), expander cone (13), expander shaft (14), and expander assembly (15).• Expander bearing driver number 1 inside diameter is 28.575–37.465 mm (1.125–1.475 in) and is used with theexpander assembly and the small washer.• Expander bearing driver number 2 inside diameter is 37.465–43.18 mm (1.475–1.7 in) and is used with number 1expanding driver and the small washer.• Expander bearing driver number 3 inside diameter is 43.18–48.895 mm (1.7–1.925 in) and is used with number 2expanding driver and the large washer.126 of 272
Print Preview Version 8.0 PubTeX output 2006.06.15:1036 File: C:\DOCUME~1\PCOMPO~1.IGS\LOCALS~1\Temp\.aptcache\2006LS7/tfa01804.dvi User: PComposer Page: 1272006 Y Car GMX245 Corvette7.0L (LS7) Engine Mechanical• Expander bearing driver number 4 inside diameter is 48.895–54.61 mm (1.925–2.15 in) and is used with number 3expanding driver and the large washer.• Expander bearing driver number 5 inside diameter is 54.61–60.325 mm (2.150–2.375 in) and is used with number 4expanding driver and the large washer.• Expander bearing driver number 6 inside diameter is 60.325–68.326 mm (2.375–2.69 in) and is used with number 5expanding driver and the large washer.Tool Assembly and Operation1. Select the proper expanding driver and washer from the expanding driver and washer information.Important: To install or remove the expanding driver, always push on or pull from the ends.Pressure on the outside diameter may cause a bind against the rubber expanding sleeve.2. Place the expanding driver onto the expander assembly.3. Ensure the separation lines between the segments of the expanding driver align with the separation linesof the expander assembly.4. With the small end of the cone facing the driver assembly, place the guide cone over the driving bar.5. Place the driving washer over the threaded portion of the expander assembly.6. Screw the expander assembly, with driving washer, onto the driving bar.For removal of the inner bearings, it may be necessary to install the driver bar extension.15525577. Insert the tool into an inner camshaft bearing and tighten until snug.Operate the tool from the front or rear of the engine block.On some engine blocks, the nut on the expander assembly is inaccessible, except from either end. In this case,you must use a socket and extension to enlarge and reduce the expander assembly.8. Slide the nylon cone (2) into the front or rear camshaft bearing. This will properly align the tool.9. Drive the bearing out of the engine block.10. Repeat the procedure for the additional inner bearings.127 of 272
Page 1 and 2:
Print Preview Version 8.0 PubTeX ou
Page 3:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76: Print Preview Version 8.0 PubTeX ou
Page 125: Print Preview Version 8.0 PubTeX ou
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
show all

LS7 Corvette Mechanical Repair Specs (PDF) - Bakes Online

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?