LS7 Corvette Mechanical Repair Specs (PDF) - Bakes Online

More documents

Recommendations

Info

Print Preview Version 8.0 PubTeX output 2006.06.15:1036 File: C:\DOCUME~1\PCOMPO~1.IGS\LOCALS~1\Temp\.aptcache\2006LS7/tfa01804.dvi User: PComposer Page: 2402006 Y Car GMX245 Corvette7.0L (LS7) Engine Mechanical1552477Notice: Refer to Fastener Notice .Important:• Tighten the exhaust manifold bolts, as specified in the service procedure. Improperly installed and/or leakingexhaust manifold gaskets may affect vehicle emissions and/or on-board diagnostic (OBD) II system performance.• The cylinder head exhaust manifold bolt hole threads must be clean and free of debris or threadlockingmaterial.• Do not apply sealant to the first 3 threads of the bolts.1. Install the heat shield (603) and bolts (604).Tighten: Tighten the bolts to 9 N·m (80 lb in).2. Install the studs (605).Tighten: Tighten the studs to 20 N·m (15 lb ft).15525303. Apply a 5 mm (0.2 in) wide band of threadlock GM P/N 12345493 (Canadian P/N 10953488), or equivalent, to thethreads of the exhaust manifold bolts. Refer to Sealers, Adhesives, and Lubricants .4. Install the exhaust manifold, NEW gasket, and bolts.Tighten:240 of 272
Print Preview Version 8.0 PubTeX output 2006.06.15:1036 File: C:\DOCUME~1\PCOMPO~1.IGS\LOCALS~1\Temp\.aptcache\2006LS7/tfa01804.dvi User: PComposer Page: 2412006 Y Car GMX245 Corvette7.0L (LS7) Engine Mechanical5. Tighten the exhaust manifold bolts a first pass to 15 N·m (11 lb ft). Tighten the exhaust manifold boltsbeginning with the center 2 bolts. Alternate from side-to-side, working toward the outside bolts.6. Tighten the exhaust manifold bolts a final pass to 20 N·m (15 lb ft). Tighten the exhaust manifold boltsbeginning with the center 2 bolts. Alternate from side-to-side, working toward the outside bolts.7. Using a flat punch, bend over the exposed edge of the exhaust manifold gasket at the front of the right cylinder head.Repair Instructions1556304Clutch Pilot Bearing InstallationTools RequiredJ 38836 Bushing Installer and Clutch Arbor2601311. Install a 5/8 inch washer (1) onto the J 38836 , or equivalent.The washer serves as a stop against the crankshaft face and assists in installing the bearing to the proper depth.2. Install the new pilot bearing (2) onto the tool.241 of 272
Page 1 and 2:
Print Preview Version 8.0 PubTeX ou
Page 3:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190: Print Preview Version 8.0 PubTeX ou
Page 239: Print Preview Version 8.0 PubTeX ou
show all

LS7 Corvette Mechanical Repair Specs (PDF) - Bakes Online

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?