LS7 Corvette Mechanical Repair Specs (PDF) - Bakes Online

More documents

Recommendations

Info

Print Preview Version 8.0 PubTeX output 2006.06.15:1036 File: C:\DOCUME~1\PCOMPO~1.IGS\LOCALS~1\Temp\.aptcache\2006LS7/tfa01804.dvi User: PComposer Page: 2082006 Y Car GMX245 Corvette7.0L (LS7) Engine Mechanical1699207Important: For proper orientation, note the installation direction of the oil seal. The oil seal is a reverse-lip design.The part number is applied to the outside face of the seal, as shown.1. Inspect the seal and identify the part number markings for proper orientation.632002. Install the J 41479 or J 41479-2A cone (2) and bolts onto the rear of the crankshaft. J 41479-2A may be requiredfor manual transmission applications.3. Tighten the bolts until snug. Do not overtighten.4. Install the rear oil seal onto the tapered cone (2) and push the seal to the rear seal bore. Install the oil seal withthe part number markings facing away from the engine.5. Thread the J 41479 threaded rod into the tapered cone until the tool (1) contacts the oil seal.6. Align the oil seal onto the tool (1).7. Rotate the handle of the tool (1) clockwise until the seal enters the rear housing and bottoms into the seal bore.8. Remove the tool.Repair Instructions1556262208 of 272
Print Preview Version 8.0 PubTeX output 2006.06.15:1036 File: C:\DOCUME~1\PCOMPO~1.IGS\LOCALS~1\Temp\.aptcache\2006LS7/tfa01804.dvi User: PComposer Page: 2092006 Y Car GMX245 Corvette7.0L (LS7) Engine MechanicalEngine Front Cover InstallationTools Required• EN-47812 Installer Bolt• EN-47813 Front Cover Alignment• J 41480 Front and Rear Cover Alignment1552543Important:• Do not use the crankshaft oil seal or the engine front cover gasket again.• Do not apply any type of sealant to the front cover gasket, unless specified.• The special tools in this procedure are used to properly align the engine front cover at the oil pan surfaceand to center the crankshaft front oil seal.– All gasket surfaces should be free of oil or other foreign material during assembly.The crankshaft front oil seal MUST be centered in relation to the crankshaft.– The oil pan sealing surface at the front cover, and the engine block, MUST be aligned within specifications.– An improperly aligned front cover may cause premature front oil seal wear and/or engine assembly oil leaks.1. Install the front cover gasket (503), front cover (502), and bolts (501).2. Tighten the cover bolts finger tight. Do not overtighten.209 of 272
Page 1 and 2:
Print Preview Version 8.0 PubTeX ou
Page 3:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158: Print Preview Version 8.0 PubTeX ou
Page 207: Print Preview Version 8.0 PubTeX ou
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
show all

LS7 Corvette Mechanical Repair Specs (PDF) - Bakes Online

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?