LS7 Corvette Mechanical Repair Specs (PDF) - Bakes Online

More documents

Recommendations

Info

Print Preview Version 8.0 PubTeX output 2006.06.15:1036 File: C:\DOCUME~1\PCOMPO~1.IGS\LOCALS~1\Temp\.aptcache\2006LS7/tfa01804.dvi User: PComposer Page: 2382006 Y Car GMX245 Corvette7.0L (LS7) Engine MechanicalWater Pump Installation1552531Important: All gasket surfaces are to be free of oil or other foreign material during assembly.1. Install the water pump (300) and NEW gaskets (306).Notice: Refer to Fastener Notice .2. Install the water pump bolts (301).Tighten:3. Tighten the water pump bolts a first pass to 15 N·m (11 lb ft).4. Tighten the water pump bolts a final pass to 30 N·m (22 lb ft).Repair Instructions1556301Exhaust Manifold Installation - Left Side1552472238 of 272
Print Preview Version 8.0 PubTeX output 2006.06.15:1036 File: C:\DOCUME~1\PCOMPO~1.IGS\LOCALS~1\Temp\.aptcache\2006LS7/tfa01804.dvi User: PComposer Page: 2392006 Y Car GMX245 Corvette7.0L (LS7) Engine MechanicalNotice: Refer to Fastener Notice .Important:• Tighten the exhaust manifold bolt as specified in the service procedure. Improperly installed and/or leakingexhaust manifold gaskets may affect vehicle emissions and/or on-board diagnostic (OBD) II system performance.• The cylinder head exhaust manifold bolt hole threads must be clean and free of debris or threadlockingmaterial.• Do not apply sealant to the first 3 threads of the bolts.1. Install the heat shield (603) and bolts (604).Tighten: Tighten the bolts to 9 N·m (80 lb in).2. Install the studs (605).Tighten: Tighten the studs to 20 N·m (15 lb ft).15525293. Apply a 5 mm (0.2 in) wide band of threadlock GM P/N 12345493 (Canadian P/N 10953488), or equivalent, to thethreads of the exhaust manifold bolts. Refer to Sealers, Adhesives, and Lubricants .4. Install the exhaust manifold, NEW gasket, and bolts.Tighten:5. Tighten the exhaust manifold bolts a first pass to 15 N·m (11 lb ft). Tighten the exhaust manifold boltsbeginning with the center 2 bolts. Alternate from side-to-side, working toward the outside bolts.6. Tighten the exhaust manifold bolts a final pass to 20 N·m (15 lb ft). Tighten the exhaust manifold boltsbeginning with the center 2 bolts. Alternate from side-to-side, working toward the outside bolts.7. Using a flat punch, bend over the exposed edge of the exhaust manifold gasket at the rear of the left cylinder head.Repair Instructions1556302Exhaust Manifold Installation - Right Side239 of 272
Page 1 and 2:
Print Preview Version 8.0 PubTeX ou
Page 3:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188: Print Preview Version 8.0 PubTeX ou
Page 237: Print Preview Version 8.0 PubTeX ou
show all

LS7 Corvette Mechanical Repair Specs (PDF) - Bakes Online

Create successful ePaper yourself

Delete template?

Save as template?