LS7 Corvette Mechanical Repair Specs (PDF) - Bakes Online

More documents

Recommendations

Info

Print Preview Version 8.0 PubTeX output 2006.06.15:1036 File: C:\DOCUME~1\PCOMPO~1.IGS\LOCALS~1\Temp\.aptcache\2006LS7/tfa01804.dvi User: PComposer Page: 2062006 Y Car GMX245 Corvette7.0L (LS7) Engine Mechanical63243Important: To properly align the rear housing, the J 41476 must be installed onto the rear of the crankshaft withthe tool mounting bolts parallel to the oil pan surface.5. Rotate the crankshaft until 2 opposing flywheel bolt holes are parallel to the oil pan surface.65286Important: The tapered legs of the alignment tool must enter the rear housing oil seal bore.6. Install the J 41476 and bolts onto the rear of the crankshaft.Tighten:7. Tighten the tool mounting bolts until snug. Do not overtighten.8. Tighten the J 41480 tool-to-rear housing bolts evenly to 12 N·m (106 lb in).9. Tighten the rear housing bolts to 30 N·m (22 lb ft).10. Remove the tools.206 of 272
Print Preview Version 8.0 PubTeX output 2006.06.15:1036 File: C:\DOCUME~1\PCOMPO~1.IGS\LOCALS~1\Temp\.aptcache\2006LS7/tfa01804.dvi User: PComposer Page: 2072006 Y Car GMX245 Corvette7.0L (LS7) Engine Mechanical6324011. Measure the rear housing-to-engine block oil pan surface for flatness.11.1. Place a straight edge onto the engine block and rear housing oil pan sealing surfaces.Avoid contact with the portion of the gasket that protrudes into the oil pan surface.11.2. Insert a feeler gage between the rear housing and the straight edge. The housing must be flushwith the oil pan or no greater than 0.5 mm (0.02 in) below flush.12. If the rear housing-to-engine block oil pan surface alignment is not within specifications, repeat the housingalignment procedure.13. If the correct rear housing-to-engine block alignment at the oil pan surface cannot be obtained, replace therear housing.Repair Instructions1765631Crankshaft Rear Oil Seal InstallationTools Required• J 41479 Crankshaft Rear Oil Seal Installer• J 41479-2A Crankshaft Rear Oil Seal Installation Guide207 of 272
Page 1 and 2:
Print Preview Version 8.0 PubTeX ou
Page 3:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156: Print Preview Version 8.0 PubTeX ou
Page 205: Print Preview Version 8.0 PubTeX ou
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
show all

LS7 Corvette Mechanical Repair Specs (PDF) - Bakes Online

Create successful ePaper yourself

Delete template?

Save as template?