LS7 Corvette Mechanical Repair Specs (PDF) - Bakes Online

More documents

Recommendations

Info

Print Preview Version 8.0 PubTeX output 2006.06.15:1036 File: C:\DOCUME~1\PCOMPO~1.IGS\LOCALS~1\Temp\.aptcache\2006LS7/tfa01804.dvi User: PComposer Page: 1902006 Y Car GMX245 Corvette7.0L (LS7) Engine Mechanical15524945. Install the M10 bolts (129) and studs (128).6. Using a plastic-face hammer, tap the bearing caps into place.7. Install the NEW M8 bearing cap side bolts (127).63214Notice: Refer to Fastener Notice .8. Tighten the bearing cap M10 bolts (1–10).Tighten: Tighten the M10 bearing cap bolts (1–10) a first pass in sequence to 20 N·m (15 lb ft).Important: To properly align the crankshaft thrust bearings, the final thrust of the crankshaft MUST be in theforward direction.9. Using a plastic-face hammer, tap the crankshaft rearward, then forward in order to align the thrust bearings.Tighten:10. Tighten the M10 bolts (1–10) a final pass in sequence 80 degrees using the J 45059 .11. Tighten the M10 studs (11–20) a first pass in sequence to 20 N·m (15 lb ft).12. Tighten the M10 studs (11–20) a final pass in sequence 51 degrees using the J 45059 .13. Tighten the bearing cap side M8 bolts to 25 N·m (18 lb ft).Tighten the bolt on 1 side of the bearing cap and then tighten the bolt on the opposite side of the samebearing cap.190 of 272
Print Preview Version 8.0 PubTeX output 2006.06.15:1036 File: C:\DOCUME~1\PCOMPO~1.IGS\LOCALS~1\Temp\.aptcache\2006LS7/tfa01804.dvi User: PComposer Page: 1912006 Y Car GMX245 Corvette7.0L (LS7) Engine Mechanical140208314. Install the CKP sensor.14.1.used again.Inspect the CKP sensor O-ring seal (750). If the O-ring seal is not cut or damaged, it may be14.2. Coat the O-ring seal with clean engine oil.14.3. Install the O-ring onto the sensor.14.4. Install the sensor (701). Rotate the sensor until the locating hole in the bracket aligns with the bolthole in the block.14.5. Install the sensor bolt (702).Tighten: Tighten the CKP sensor bolt to 25 N·m (18 lb ft).6431615. Measure the crankshaft end play.15.1. Thrust the crankshaft forward or rearward.15.2. Insert a feeler gage between the center crankshaft bearing and the bearing surface of thecrankshaft and measure the bearing clearance.The proper crankshaft end play clearance is 0.04–0.2 mm (0.0015–0.0078 in).191 of 272
Page 1 and 2:
Print Preview Version 8.0 PubTeX ou
Page 3:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140: Print Preview Version 8.0 PubTeX ou
Page 189: Print Preview Version 8.0 PubTeX ou
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
show all

LS7 Corvette Mechanical Repair Specs (PDF) - Bakes Online

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?