LS7 Corvette Mechanical Repair Specs (PDF) - Bakes Online

More documents

Recommendations

Info

Print Preview Version 8.0 PubTeX output 2006.06.15:1036 File: C:\DOCUME~1\PCOMPO~1.IGS\LOCALS~1\Temp\.aptcache\2006LS7/tfa01804.dvi User: PComposer Page: 2142006 Y Car GMX245 Corvette7.0L (LS7) Engine Mechanicalimportant that the rear of the block and the rear of the oil pan are flush, or even. The rear of the oil pan mustNEVER protrude beyond the engine block and transmission housing plane.• Do not use the oil pan gasket again.• It is not necessary to rivet the NEW gasket to the oil pan.1. Apply a 5 mm (0.2 in) bead of sealant GM P/N 12378521 (Canadian P/N 88901148), or equivalent, 20 mm (0.8 in)long to the engine block. Apply the sealant directly onto the tabs of the front cover gasket that protrude into the oil pansurface. Refer to Sealers, Adhesives, and Lubricants .631752. Apply a 5 mm (0.2 in) bead of sealant GM P/N 12378521 (Canadian P/N 88901148), or equivalent, 20 mm (0.8 in)long to the engine block. Apply the sealant directly onto the tabs of the rear housing gasket that protrude into the oilpan surface.15525423. Pre-assemble the oil pan gasket to the pan.3.1. Install the gasket onto the oil pan.3.2. Install the oil pan bolts (439, 453) to the pan and through the gasket.4. Install the oil pan (400), gasket and bolt to the engine block.5. Tighten the bolts finger tight. Do not overtighten.214 of 272
Print Preview Version 8.0 PubTeX output 2006.06.15:1036 File: C:\DOCUME~1\PCOMPO~1.IGS\LOCALS~1\Temp\.aptcache\2006LS7/tfa01804.dvi User: PComposer Page: 2152006 Y Car GMX245 Corvette7.0L (LS7) Engine Mechanical15525656. Place a straight edge across the rear of the engine block and the rear of the oil pan at the transmission housingmounting surfaces.Notice: Refer to Fastener Notice .7. Align the oil pan until the rear of the engine block and the rear of the oil pan are flush, or even.Tighten:8. Tighten the oil pan-to-block and oil pan-to-front cover bolts to 25 N·m (18 lb ft).9. Tighten the oil pan-to-rear cover bolts to 12 N·m (106 lb in).10. Measure the oil pan-to-engine block alignment.10.1. Place a straight edge across the rear of the engine block and rear of oil pan at the transmissionhousing mounting surfaces.Important: The rear of the oil pan must NEVER protrude beyond the engine block and transmission housingmounting surfaces.10.2. Insert a feeler gage between the straight edge and the oil pan transmission housing mountingsurface, and inspect to ensure there is no greater than a 0.1 mm (0.004 in) gap (a) between the pan and straight edge.10.3. If the oil pan alignment is not within specifications, remove the oil pan and repeat the aboveprocedure.Repair Instructions1556267Oil Filter and Adapter Installation215 of 272
Page 1 and 2:
Print Preview Version 8.0 PubTeX ou
Page 3:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164: Print Preview Version 8.0 PubTeX ou
Page 213: Print Preview Version 8.0 PubTeX ou
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
show all

LS7 Corvette Mechanical Repair Specs (PDF) - Bakes Online

Create successful ePaper yourself

Delete template?

Save as template?