Tracer AV Installation Manual - Rice Lake Weighing Systems

More documents

Recommendations

Info

3.1.5 Editing Integers1. By pressing Units , navigate all the way to theright (beyond all ‘-’ characters until there are nosegments flashing).NOTE: The ‘-’ characters are placeholders for appending orremoving digits at the end of numbers that exceed thesix-digit display.2. Press Zero to accept the modified value.3.1.6 Editing Floating Point (Decimal Point Position)1. By pressing Units , navigate all the way to theright (beyond all ‘-’ characters until there are nosegments flashing).2. Press Zero to initialize editing of decimal pointposition.3. Press Units to move the decimal point to the desired position.The decimal point will move forward one position with the UnitsIncrement Value/Save Value EnteredAnd Return to LevelAbovebutton is pressed to select the position.4. When the decimal point is in the desired position, press Zero .Change Digit SelectionFigure 3-3. Editing Procedure for Numeric Valuesbutton and wrap around until the Zero3.2 Menu Structures and Parameter DescriptionsThe following sections provide graphic representations of the Tracer AV menu structures. In the actual menustructure, the settings you choose under each parameter are arranged horizontally. To save page space, menuchoices are shown in vertical columns. The factory default setting appears at the top of each column in bold type.Most menu diagrams are accompanied by a table that describes all parameters and parameter values associatedwith that menu. Default parameter values are shown in bold type.3.2.1 Default Calibration MenuXXXXXXX DEFCALCONFIG XXXXXXX FORMAT CALIBR SERIAL PROGRM XXXXXXX SETPNT VERSSELECT WZEROWV AL WSPAN500lb300lbFigure 3-4. Default Calibration MenuDEFCAL MenuParameter Choices DescriptionSELECT500lb300lb500lb sets the scale to a primary of 500lb x 1 lb and a secondary of 250kg x .5 kg ;SP1 trip=50lb; SP2=off; Dig Filter 1=8; Dig Filter 2=8; Dig Filter 3=8; Zero Tracking=3D300lb sets the scale to a primary of 300lb x 1 lb and a secondary of 150kg x .5kgSP1 trip=50lb; SP2=off; Dig Filter 1=8; Dig Filter 2=8; Dig Filter 3=8; Zero Tracking = 3DWZERO — Display and edit the zero calibration A/D count value.DO NOT adjust this value after WSPAN has been set!WVAL — Display and edit the test weight value.WSPAN — Display and edit the span calibration A/D count value.Table 3-3. Default Calibration Parameters12 Tracer AV Installation Manual
3.2.2 Configuration MenuDEFCALCONFIGXXXXXXX FORMATCALIBRSERIALPROGRMXXXXXXX SETPNTVERSGRADSZTRKBNZRANGEMOTBANOVRLOASMPRAT10000 1.9000001FS+2%15HZnumbernumber number numberFS+1D30HZFS+9D60HZFS7.5HZDIGFL1DIGFL2DIGFL3DFSENSDFTHRHT AREFN8888OUTNONEBOTH16161616OUT2DDNOT ARE32323232OUT5DDPBTARE64646464OUT10DDKEYED111128OUT20DD2222OUT50DD4444OUT100DD200DD250DDFigure 3-5. Configuration MenuCONFIG MenuParameter Choices DescriptionLevel 2 submenusGRADS 1000numberZTRKBN 0numberZRANGE 1.900000numberGraduations. Specifies the number of full scale graduations. The value entered must be inthe range 1–100 000 and should be consistent with legal requirements and environmentallimits on system resolution.To calculate GRADS, use the formula, GRADS = Capacity / Display Divisions.Display divisions for primary and secondary units are specified on the FORMAT menu.Automatically zeroes the scale when within the range specified, as long as the input iswithin the ZRANGE and scale is at standstill. Specify the zero tracking band in ± displaydivisions. Maximum legal value varies depending on local regulations.NOTE: For scales using linear calibration, do not set the zero tracking band to a valuegreater than that specified for the first linearization point.Selects the range within which the scale can be zeroed. The 1.900000 default value is ±1.9% around the calibrated zero point, for a total range of 3.8%. Indicator must be atstandstill to zero the scale. Use the default value for legal-for-trade applications.Table 3-4. Configuration Menu ParametersTracer AV Installation Manual - Configuration 13
Page 4 and 5: 5.0 EDP Commands...................
Page 6 and 7: 1.2 Display and KeypadFigure 1-1 sh
Page 8 and 9: Figure 2-2. Tracer AV (back) securi
Page 10 and 11: Figure 2-6. Remote Display CutoutFi
Page 12 and 13: There are two socketed DB-9 connect
Page 14 and 15: 3.0 ConfigurationTo configure the T
Page 18 and 19: CONFIG MenuMOTBAN 1numberOVRLOASMPR
Page 20 and 21: FORMAT MenuLevel 3 submenusPrimary
Page 23 and 24: 3.2.6 Program MenuDEFCALCONFIGXXXXX
Page 27: 4.0 CalibrationThe Tracer AV can be
Page 30 and 31: 5.0 EDP CommandsThe Tracer AV can b
Page 32 and 33: Command Description ValuesPRI.DECPN
Page 34 and 35: 5.1.6 Normal Mode CommandsThe seria
Page 36 and 37: 6.0 Appendix6.1 Error MessagesThe T
Page 38 and 39: 6.3 Continuous Output (Stream) Form
Page 40 and 41: 6.5 Conversion Factors for Secondar
Page 42 and 43: 6.6.3 Setting the Digital Filter Pa
Page 44 and 45: 6.8 Regulatory Mode FunctionsREGULA
Page 46: Tracer AV Limited WarrantyRice Lake

Tracer AV Installation Manual - Rice Lake Weighing Systems

Create successful ePaper yourself

Delete template?

Save as template?