Tracer AV Installation Manual - Rice Lake Weighing Systems

More documents

Recommendations

Info

5.1.6 Normal Mode CommandsThe serial transmit weight data commands (see Table 5-12) transmit data to the EDP port on demand. The SXand EX commands are valid only in normal operating mode; all other commands are valid in either setup ornormal mode.Command Description Response FormatUID Set unit ID nnnnnnnSD Set date MMDDYY, DDMMYY, YYMMDD (enter using DATEFMTspecified)ST Set time hhmm (enter using 24-hour format)SX Start EDP streaming OK or ??EX Stop EDP streaming OK or ??RS Reset system —XG Transmit gross weight in displayed units nnnnnn UUXN Transmit net weight in displayed unitswhere nnnnnn is the weight value, UU is the units.XT Transmit tare weight in displayed unitsXG2 Transmit gross weight in non-displayed unitsXN2 Transmit net weight in non-displayed unitsXT2 Transmit tare weight in non-displayed unitsXE Query system error conditions nnnnn nnnnnSee Section 6.1.2 on page 33 for detailed information aboutthe XE command response format.Table 5-12. Normal Mode Commands30 Tracer AV Installation Manual
5.2 Saving and Transferring DataConnecting a personal computer to the Tracer AV EDPport allows you to save configuration data to the PC orto download configuration data from the PC to aTracer AV. The following sections describe theprocedures for these save and transfer operations.5.2.1 Saving Tracer AV Data to a Personal ComputerConfiguration data can be saved to a personalcomputer connected to the EDP port. The PC must berunning a communications program such asPROCOMMPLUS ® . See Section 2.3.3 on page 7 forinformation about serial communications wiring andEDP port pin assignments.When configuring the Tracer AV, ensure that thevalues set for the BAUD and BITS parameters on theSERIAL menu match the baud rate, bits, and paritysettings configured for the serial port on the PC. Setthe PRNDEST parameter to EDP.To save all configuration data, place the Tracer AV insetup mode and send the DUMPALL EDP command.The Tracer AV responds by sending all configurationparameters to the PC as ASCII-formatted text.5.2.2 Downloading Configuration Data from PC toTracer AVConfiguration data saved on a PC or floppy disk canbe downloaded from the PC to a Tracer AV. Thisprocedure is useful when a number of Tracer AVs withsimilar configurations are set up or when a Tracer AVis replaced.To download configuration data, connect the PC to theEDP port as described in Section 5.2.1. Place theTracer AV in setup mode and use the PCcommunications software to send the savedconfiguration data to the Tracer AV. When transfer iscomplete, calibrate the Tracer AV as described inSection 4.0.NOTES:• Calibration settings are included in theconfiguration data downloaded to the TracerAV. If the receiving Tracer AV is a directreplacement for another Tracer AV and theattached scale is not changed, recalibration isnot required.• When downloading configurations thatinclude changed serial communicationssettings, edit the data file to place the serialcommunications changes at the end of thefile. Communication between the PC andTracer AV will be lost once the Tracer AVreceives settings for baud rate (BAUDparameter) or data bits and parity (BITSparameter) that do not match those configuredfor the PC.Tracer AV Installation Manual - EDP Commands 31
Page 4 and 5: 5.0 EDP Commands...................
Page 6 and 7: 1.2 Display and KeypadFigure 1-1 sh
Page 8 and 9: Figure 2-2. Tracer AV (back) securi
Page 10 and 11: Figure 2-6. Remote Display CutoutFi
Page 12 and 13: There are two socketed DB-9 connect
Page 14 and 15: 3.0 ConfigurationTo configure the T
Page 16 and 17: 3.1.5 Editing Integers1. By pressin
Page 18 and 19: CONFIG MenuMOTBAN 1numberOVRLOASMPR
Page 20 and 21: FORMAT MenuLevel 3 submenusPrimary
Page 23 and 24: 3.2.6 Program MenuDEFCALCONFIGXXXXX
Page 27: 4.0 CalibrationThe Tracer AV can be
Page 30 and 31: 5.0 EDP CommandsThe Tracer AV can b
Page 32 and 33: Command Description ValuesPRI.DECPN
Page 36 and 37: 6.0 Appendix6.1 Error MessagesThe T
Page 38 and 39: 6.3 Continuous Output (Stream) Form
Page 40 and 41: 6.5 Conversion Factors for Secondar
Page 42 and 43: 6.6.3 Setting the Digital Filter Pa
Page 44 and 45: 6.8 Regulatory Mode FunctionsREGULA
Page 46: Tracer AV Limited WarrantyRice Lake

Tracer AV Installation Manual - Rice Lake Weighing Systems

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?