Tutorials Mill Level 1 Training - TechEdu.com

More documents

Recommendations

Info

Mill Level 1 TUTORIAL 7During the geometry creation of this tutorial, if you make a mistake, to undo the last step you can use theUndo icon. You can undo as many steps as needed. If you delete or undo a step by mistake, just usethe Redo icon.STEP 2: CREATE THE 9/16“ AND 3/8“ DIAMETER CIRCLES KNOWING THE CENTERPOINT AND THE DIAMETERStep Preview:2.1 Create the two 9/16 diameter circlesCreateArcCircle Center PointEnter the Diameter value9/16 (Enter).To be able to create more than one circle with the same diameter, select the diameter icontolock the value.[Enter the center point]: Select the center point of the fillet arcs as shown in the following twopictures.Select the centerof the fillet arcPage 7-5
Mill Level 1 TUTORIAL 7Select the Apply button.2.2 Create the two 3/8 diameter circlesChange the diameter to 0.375 and leave it locked (Press Enter)[Enter the center point]: Select the center point of the fillet arcs as shown in the following twopictures.Page 7-6
Page 2: Mill Level 1 Training TutorialsToor
Page 6: TUTORIALSERIESFORHOWTOUSETHISBOOKTh
Page 9 and 10: TUTORIAL SERIES FORTUTORIAL #7LEVEL
Page 12 and 13: Mill Level 1 TUTORIAL 7GEOMETRY CRE
Page 16 and 17: Mill Level 1 TUTORIAL 7Select the A
Page 18 and 19: Mill Level 1 TUTORIAL 7[ Select a l
Page 20 and 21: Mill Level 1 TUTORIAL 74.3 Remove p
Page 22 and 23: Mill Level 1 TUTORIAL 7STEP 5: CREA
Page 24 and 25: Mill Level 1 TUTORIAL 75.2 Creating
Page 26 and 27: Mill Level 1 TUTORIAL 75.4 Creating
Page 28 and 29: Mill Level 1 TUTORIAL 7Select the T
Page 30 and 31: Mill Level 1 TUTORIAL 7[ Select ent
Page 32 and 33: Mill Level 1 TUTORIAL 7The final ge
Page 34 and 35: Mill Level 1 TUTORIAL 7STEP 8: SELE
Page 36 and 37: Mill Level 1 TUTORIAL 7Select the O
Page 38 and 39: Mill Level 1 TUTORIAL 7Select the l
Page 44 and 45: Mill Level 1 TUTORIAL 710.5 Set the
Page 46 and 47: Mill Level 1 TUTORIAL 7Click on the
Page 48 and 49: Mill Level 1 TUTORIAL 7Select the R
Page 50 and 51: Mill Level 1 TUTORIAL 7Copy the geo
Page 52 and 53: Mill Level 1 TUTORIAL 712.4 Set the
Page 54 and 55: Mill Level 1 TUTORIAL 713.2 Modify
Page 56 and 57: Mill Level 1 TUTORIAL 7Select the P
Page 58 and 59: Mill Level 1 TUTORIAL 7Initial stoc
Page 60 and 61: Mill Level 1 TUTORIAL 7STEP 16: CRE
Page 62 and 63: Mill Level 1 TUTORIAL 7Select Top V
Page 64 and 65:
Mill Level 1 TUTORIAL 7STEP 18: FAC
Page 66 and 67:
Mill Level 1 TUTORIAL 7From the Tre
Page 68 and 69:
Mill Level 1 TUTORIAL 719.2 Select
Page 70 and 71:
Mill Level 1 TUTORIAL 7From the ext
Page 72 and 73:
Mill Level 1 TUTORIAL 719.4 Set the
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Mill Level 1 TUTORIAL 7Select only
Page 80 and 81:
Page 82 and 83:
Mill Level 1 TUTORIAL 723.3 Set the
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Mill Level 1 TUTORIAL 7STEP 26: VER
Page 92:
Mill Level 1 TUTORIAL 7Select the r
Page 96 and 97:
Mill Level 1 TUTORIAL 7Student prac
Page 98:
Mill Level 1 TUTORIAL 7TUTORIAL 7 Q
show all

Tutorials Mill Level 1 Training - TechEdu.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?