Tutorials Mill Level 1 Training - TechEdu.com

More documents

Recommendations

Info

Mill Level 1 TUTORIAL 7Select Top View and click on the Set your current WCS, construction plane and tool plane withtheir origins to the selected view button.Select the OK button.Select the Isometric view.Select Fit button.The part should look as shown to theright.Note that the origin is set at top of thepart at the lower left corner. Follow nextsub step if you want to move the originat the upper left corner.17.2 Using WCS to set the origin at the upper left cornerSelect WCS in the Status Bar.Select View Manager.Page 7-53
Mill Level 1 TUTORIAL 7Click on the Select button in the Origin area as shown.[Select a point]: Select Endpoint A.Select Endpoint AChange the Z value in the Origin area to 0 to set again the part zero at the finish size.The new origin coordinates should look as shown.Select the OK button to exit View Manger.Note that the grid moves at the upper left corner at the top of the part at the finished size.Page 7-54
Page 2:
Mill Level 1 Training TutorialsToor
Page 6:
TUTORIALSERIESFORHOWTOUSETHISBOOKTh
Page 9 and 10:
TUTORIAL SERIES FORTUTORIAL #7LEVEL
Page 12 and 13: Mill Level 1 TUTORIAL 7GEOMETRY CRE
Page 14 and 15: Mill Level 1 TUTORIAL 7During the g
Page 16 and 17: Mill Level 1 TUTORIAL 7Select the A
Page 18 and 19: Mill Level 1 TUTORIAL 7[ Select a l
Page 20 and 21: Mill Level 1 TUTORIAL 74.3 Remove p
Page 22 and 23: Mill Level 1 TUTORIAL 7STEP 5: CREA
Page 24 and 25: Mill Level 1 TUTORIAL 75.2 Creating
Page 26 and 27: Mill Level 1 TUTORIAL 75.4 Creating
Page 28 and 29: Mill Level 1 TUTORIAL 7Select the T
Page 30 and 31: Mill Level 1 TUTORIAL 7[ Select ent
Page 32 and 33: Mill Level 1 TUTORIAL 7The final ge
Page 34 and 35: Mill Level 1 TUTORIAL 7STEP 8: SELE
Page 36 and 37: Mill Level 1 TUTORIAL 7Select the O
Page 38 and 39: Mill Level 1 TUTORIAL 7Select the l
Page 44 and 45: Mill Level 1 TUTORIAL 710.5 Set the
Page 46 and 47: Mill Level 1 TUTORIAL 7Click on the
Page 48 and 49: Mill Level 1 TUTORIAL 7Select the R
Page 50 and 51: Mill Level 1 TUTORIAL 7Copy the geo
Page 54 and 55: Mill Level 1 TUTORIAL 713.2 Modify
Page 56 and 57: Mill Level 1 TUTORIAL 7Select the P
Page 58 and 59: Mill Level 1 TUTORIAL 7Initial stoc
Page 60 and 61: Mill Level 1 TUTORIAL 7STEP 16: CRE
Page 64 and 65: Mill Level 1 TUTORIAL 7STEP 18: FAC
Page 66 and 67: Mill Level 1 TUTORIAL 7From the Tre
Page 68 and 69: Mill Level 1 TUTORIAL 719.2 Select
Page 70 and 71: Mill Level 1 TUTORIAL 7From the ext
Page 78 and 79: Mill Level 1 TUTORIAL 7Select only
Page 90 and 91: Mill Level 1 TUTORIAL 7STEP 26: VER
Page 92: Mill Level 1 TUTORIAL 7Select the r
Page 96 and 97: Mill Level 1 TUTORIAL 7Student prac
Page 98: Mill Level 1 TUTORIAL 7TUTORIAL 7 Q
show all

Tutorials Mill Level 1 Training - TechEdu.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?